Generally, it is a high tensil plastic or fiberglass. Some is actually constructed of nylon cord coated with a resin to keep it from clogging. Heavy duty fishing line might work, but probably will be too thin to whack down much more than the thinnest grass.
It is easy to string a dual line Remington trimmer by following the instructions in the manual. The manual was supplied with the trimmer when purchased.
To replace the weed trimmer line on a string trimmer, follow these steps: Turn off the trimmer and disconnect the power source. Remove the spool housing by pressing the tabs or unscrewing the cap. Take out the old line and cut a new piece to the appropriate length. Insert the new line into the trimmer head following the arrows for the correct direction. Reassemble the spool housing and test the trimmer.
To restring a Ryobi string trimmer, first remove the spool from the trimmer head. Cut a length of new trimmer line, thread it through the holes in the spool, and wind it evenly around the spool. Reinsert the spool into the trimmer head, and feed the line through the trimmer head eyelets. Finally, secure the spool back in place and trim any excess line.
To perform a Ryobi trimmer string replacement, first turn off the trimmer and disconnect the spark plug. Remove the spool cover and take out the old string spool. Cut a new piece of trimmer line to the appropriate length and insert it into the spool. Wind the new line evenly onto the spool in the direction indicated on the spool. Reassemble the trimmer and test the new string before use.
Watch the Youtube video.
A line trimmer, also known as a string trimmer, is used to trim grass or weeds. The piece of equipment also goes by the name of a weed eater, or weed whacker.
To reload the line on your Ryobi string trimmer, first remove the spool from the trimmer head. Cut a length of new trimmer line, usually around 10 feet, and insert one end into the spool's center hole. Wind the line evenly and tightly around the spool in the direction indicated on the spool. Leave a few inches of line unwound, then thread the line through the trimmer head's eyelet. Reassemble the spool onto the trimmer head, ensuring the line feeds through the head properly.
To replace the weed trimmer string on a trimmer, follow these steps: Turn off the trimmer and disconnect it from the power source. Remove the spool housing by pressing the tabs on the sides and pulling it out. Take out any remaining old string from the spool. Cut a length of new trimmer string according to the trimmer's specifications. Insert the ends of the string into the holes on the spool. Wind the string evenly and tightly around the spool in the direction indicated on the spool. Reassemble the spool housing and reconnect it to the trimmer. Test the trimmer to ensure the string is working properly.
To replace the string on your Ryobi string trimmer, first turn off the trimmer and disconnect the spark plug. Then, remove the spool housing and take out the old string. Cut a new piece of string to the appropriate length and feed it through the trimmer head. Wind the string in the direction indicated on the spool and secure the ends. Finally, reassemble the trimmer and test it before use.
A whipper snipper is related to a string trimmer by the fact that they both are the same thing. In other words, whipper snipper is a synonym for a string trimmer.
To refill a Ryobi string trimmer, you need to first turn off the trimmer and remove the spool cap. Then, take out the empty spool and replace it with a new one, making sure to wind the trimmer line in the correct direction. Finally, reattach the spool cap and you're ready to trim again.
To extend the string on a Ryobi trimmer, you need to follow these steps: Turn off the trimmer and disconnect it from the power source. Locate the trimmer head and remove the spool cover. Take out the old string and cut a new piece to the appropriate length. Insert the new string into the trimmer head following the arrows for the correct direction. Wind the string evenly and securely onto the spool. Reassemble the trimmer head and spool cover. Test the trimmer to ensure the string is working properly.