0
What else can I help you with?
Which type of fire sprinkler system is most common and easiest to install?
Wet pipe sprinkler
Does an auto dealer get a discount on their insurance if they install an awning over their inventory of vehicles?
Perhaps, but I doubt it, contact your agent and inquire.
Where can I get information on sprinkler systems?
Kudzu.com has information on sprinkler systems as well as Rainbird.com. Both of these websites as well as 1-800 Contractors seems to have the most information on where to get a sprinkler system as well as who to install it.
How can I install a backflow preventer for sprinkler systems?
To install a backflow preventer for sprinkler systems, follow these steps: Turn off the water supply to the sprinkler system. Locate the main water line and cut it where you want to install the preventer. Install the backflow preventer according to the manufacturer's instructions. Connect the preventer to the main water line using appropriate fittings. Turn the water supply back on and test the preventer for leaks. Ensure the preventer is properly installed and functioning correctly to prevent backflow in the sprinkler system.
How do you install a rain bird 5000 sprinkler?
bury it in the ground at the proper depth
Can an insurance company cancel your homeowners insurance if you refuse to install exterior stair rails?
As long as the contract itself has no specifically stated agreement that shows coverage is unconditional, then, as long as they give proper notice, an insurance company can cancel ANY insurance policy for ANY reason. Of course, if you disagree with the decision, you can always consult an attorney and go from there
Where to use upright sprinkler and pendent sprinkler?
: The difference between an upright head and a pendent head is, an upright sprinkler is designed to be installed upright in the branchline piping of a sprinkler system. The pendent is designed to be in the pendent or 6 o clock position, with the deflector facing downward. It is important that you always install sprinklers in accordance with their designed listing; you cannot install an upright sprinkler in the pendent position, for example. you can usually find this information with the data sheet supplied with the sprinkler. If in doubt, contact the sprinkler manufacturer. Sprinkler installation is regulated by National Fire Protection Association or NFPA for short, document number 13.. This standard gives the codes for proper location, selection, and installation of fire sprinklers.
How do you install a sprinkler system?
There are two main methods of sprinkler system installation: open trench and pulled pipe. Open trench typically uses PVC pipe and pulled pipe typically uses poly pipe. Other than the pipe and fittings, the main difference in installation will be that the pulled pipe system requires a hole and saddle tee at the location of each sprinkler head. The steps for installing an automatic sprinkler system using an open trench method are: 1. Start with a good sprinkler system design (try searching "sprinkler system designer" for support options) 2. Make sure that you have all necessary tools, equipment, and permits 3. Have Blue Stakes mark all utilities prior to any digging 4. Install a backflow prevention device according to code 5. Place flags at the location of each sprinkler head 6. Mark and dig all trenches and valve manifold locations 7. Build and install valve manifolds (preassembled valve manifolds can make this easier) 8. Connect mainline pipe from water source connection to valve manifolds 9. Lay lateral line pipe from the valve manifolds to the location of each sprinkler head 10. Install tees and swing assemblies for each sprinkler head and flush lines 11. Connect sprinkler heads to swing assemblies; set head to level with ground 12. Install sprinkler timer/controller and connect sprinkler wire from timer to valve manifolds 13. Install nozzles on sprinkler heads 14. Install valve boxes (as required) and backfill all trenches 15. Run a zone by zone test and adjust nozzle patterns
lawn sprinkler installation?
form_title=lawn sprinkler installation form_header=9623 What items will you need this system to water?*= [] Grass [] Trees [] Shrubs [] Flower beds [] Herb garden [] Vegetable garden [] Raised beds [] Hanging baskets Will the sprinkler lines need to be trenched under any existing driveways or pathways?*= {Select One,Yes,No,Don't Know} Is a time-clock required to control the system?*= {Select One,Yes,No,Don't Know} Please specify the nature of the project.*= () Install new sprinkler system in bare yard () Install new sprinkler system in existing yard () Update and add to existing sprinkler system
How can I set up a Rainbird sprinkler system in my yard?
To set up a Rainbird sprinkler system in your yard, follow these steps: Plan the layout of the sprinkler system based on your yard's size and shape. Install the necessary piping and valves according to the layout plan. Connect the sprinkler heads to the piping and adjust their positions for optimal coverage. Install a controller to program watering schedules and zones. Test the system to ensure proper functioning and make any necessary adjustments.
Is it illegal to install speed bumps in a Florida homeowners' association?
Your answer may depend on who owns the roadway. If the association owns the road, they can install any manner of amenity. If the municipality owns the road, permission may be required, or petition may be required for the municipality to install speed bumps.
Can you install speed bumps on a private road?
Yes, you can install speed bumps on a private road with the permission of the property owner or homeowners' association.
