answersLogoWhite

0

The large collapse in the magnect field.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Physics

Disconnect a small-voltage battery from a coil of many loops of wire and a large voltage is produced by?

This phenomenon is known as electromagnetic induction. When a magnetic field created by current flowing through the coil is suddenly disrupted by disconnecting the battery, it induces a large voltage in the coil according to Faraday's law of electromagnetic induction. This sudden change in magnetic field generates an electric current in the coil that produces the high voltage.


What is lost volts?

A battery is rated to supply a certain number of volts. However, it actually supplies less, because they are "lost" as the current has to get out of the battery in the first place.(The battery has internal resistance)The amount of lost volts depends on the current being drawn:The less resistance a circuit has, the more current is drawn, because it's easier to flow.Example:If the circuit has little resistance, it draws a large current and the battery's internal resistance causes more lost volts.If the circuit has high resistance, it draws a small current and there are fewer lost volts.This is why when you short-circuit a battery (give it hardly any resistance to go through) it heats up and may explode. A large current is drawn and all the volts are used by the battery's internal resistance.


What is meant by negative voltage and how it creates?

Negative voltage is just a voltage that instead of being positive is negative. If you think of a voltage as a large amount of water in a reservoir, with a pipe connecting it to a basin below, the voltage is the movement of the water from the reservoir to the basin. However, a negative voltage is more like a suction from the basin back up to the reservoir. Anyway, if you connect the black ( - ) lead of a 9V battery to the black lead of another 9V battery, then the connection between the two black wires is at 0V, or Ground, and one of the batteries' leads will be at +9V, and the other will be at -9V. Negative voltages are only really used in complex circuits, such as ones that contain Operational Amplifiers, and in general doesn't matter in hobby and simple electronics.


Which term describes a wave or series of waves produced when a large body of water is disturbed?

A tsunami.


How large currents created?

Large currents can be created by applying a high voltage across a circuit with low resistance. This causes a large flow of electrons through the circuit, resulting in a high current. The amount of current generated is determined by Ohm's Law, which states that current is directly proportional to voltage and inversely proportional to resistance.

Related Questions

Disconnect a small-voltage battery from a coil of many loops of wire and a large voltage is produced by?

This phenomenon is known as electromagnetic induction. When a magnetic field created by current flowing through the coil is suddenly disrupted by disconnecting the battery, it induces a large voltage in the coil according to Faraday's law of electromagnetic induction. This sudden change in magnetic field generates an electric current in the coil that produces the high voltage.


What are some of the most typical usages of a battery disconnect switch?

A battery disconnection switch is a special switch that is specifically designed to be able to carry a large or heavy electrical current. It allows you to turn off the voltage without the use of tools.


How does a battery disconnect work?

A "battery disconnect" is nothing more than a special SWITCH designed and manufactured to be able to carry very large [heavy] electrical current. The one with which I'm familiar mounts on the positive battery terminal after the cable has been removed, and then the cable connector is attached to the output terminal of the disconnect switch. This switch allows one to totally and completely "kill" the battery voltage to the auto circuits, without having to use a wrench to loosen a battery terminal clamp and manually "wrestle" it from the terminal.


Where is the external voltage regulator for a 1994 lebaron?

The engine computer is the voltage regulator. It is the large black box behind the battery.


Can you connect a large battery for a 600VA computer UPS?

yes, old and new battery should have same voltage rating. Battery type shud match only capacity may be large.


What is a battery discharge tester?

It is a meter with a high wattage resistor connected parallel with the meter that drains power from the battery while it is measuring the voltage it is used to test the condition of the battery if the condition is good there will not be a large voltage drop while testing the battery


When you disconnect a small voltage battery from a coil of many loops of wire and a large voltage is produced by what?

Disconnecting a small voltage source from a coil (inductor) causes a larger, often a much larger, reverse voltage spike due to the collapse of the magnetic field in the inductor coupled with the sudden absence of a current path to dissipate the electromagnetic energy. An inductor resists a change in current. The equation for an inductor is ... di/dt = V/L ... which means that the rate of change of current is proportional to voltage and inversely proportional to inductance. If you have a current established in an inductor, and then suddenly open the circuit, the inductor will attempt to maintain that current. It can't, however, because the circuit is open, having large resistance. By ohm's law, voltage is resistance times current. If you keep current constant, and make resistance large, then voltage has to also be large. In the theoretical case of an ideal inductor in an ideal circuit, the voltage spike would have infinite voltage. In practice, we see spikes of several hundred to several thousand volts, depending on the particular cirsumstances.


Replace battery for keyless remote for GM Cars?

Generally the solution to these problems is don't disconnect the battery from the car. In order to change you battery you need to connect a small 12 volt battery to the terminals before you disconnect the car battery. It need not be a large battery since the drain will be minimal and the time short. A set of flashlight batteries works fine. Mercedes are particularily difficult because you loose the radio among other things if you disconnect the battery. You must get a dealer to reset it. This negates anything you save by installing your own battery. Note a battery charger also works.


What working of resistor?

The main power producers in an electrical system are the battery and alternator. The alternator puts 14 volts of alternating current into the electrical system and resistors. The resistors only allow a fraction of the AC voltage produced to reach the systems' sensitive components


Will transformer operate if a battery is used for the input voltage across the primary?

Transformers only work on a.c. This is because it's necessary to have a changing primary current in order to induce a voltage into the secondary winding.If you connect a battery across a transformer, it will not work. Furthermore, if the voltage of the battery matches that of the rated primary voltage, the resulting very large d.c. current is likely to overheat the primary windings and even burn it out.


How do you replace a starter on a 1993 Ford Ranger?

# Disconnect negative battery cable # Raise truck and support it # Disconnect the large cable from the terminal on the starter # Remove 4 bolts or nuts securing the starter and remove the starter from engine


Have a 1992 Dodge Ram 50 When you turn the key the lights on the dash come on but the starter does nothing you have had the Battery tested the starter tested you have replaced the ECM and Starter?

You should locate and test the solenoid. Most have three connections. There is a large cable from the battery to the solenoid, from the solenoid to the starter and from the start switch to the solenoid. The power terminals to the battery and the starter are large and have large cables. The starter switch connection is much smaller. Turning the key to 'start' provides a low current voltage to the solenoid causing the solenoid relay to close and power from the battery cable to connect through to the starter. If that voltage is present then the solenoid or the wiring between the solenoid and battery or solenoid and starter is suspect. If that voltage is missing then the starter switch or solenoid feed line may have failed.