0
You actually only need two things to make a circuit. One is a power source, such as a batter, and the other is a conductive metal, e.g. copper wire. All you need to do is touch one end of the metal to one pole of the source, and the other end of the metal to the other pole, then vioala! You have a circuit.
What else can I help you with?
An electric DC circuit is attached to a 12 volt battery and has a 3 ohm resistor in it find the current flowing through the circuit?
If the 3-ohm resistor is the ONLY thing in the circuit, then the current flowing through it is (12 volts)/(3 ohms) = 4 amperes. If there are other things in the circuit besides the resistor, then the current depends on all of them.
Which uses more energy parallel circuit or a series circuit?
That depends. For example, if the circuit is consisted of two resistors, 2 ohms each, the equivalent resistance (Req) of these two resistors in series is 4 ohms, and the Req of these two resistors in parallel is 1 ohm. If the same voltage is applied, say 4 V.power consumed in a resistance = V2/R.The parallel circuit: Power = 4 * 4 / 1 = 16 [W].The series circuit: Power = 4 * 4 / 4 = 4 [W].With everything else the same, a parallel circuit consumes more energy than a series circuit.Note that circuits of only simple resistors are discussed. You need to consider each circuit on its merit.================================AnswerIt depends. In both cases, the total energy expended will be the sum of the energies expended by each individual load.
What are 4 possible energy sources for a circuit?
Battery: Provides direct current (DC) energy for a circuit. Solar panel: Converts sunlight into electrical energy for a circuit. Generator: Converts mechanical energy into electrical energy for a circuit. Power supply: Converts alternating current (AC) from the main grid into usable energy for a circuit.
What are things that weigh 4 pounds?
Examples of things that weigh around 4 pounds include a pineapple, a quart of milk, or a small newborn baby.
What is the difference in a parallel circuit and a series circuit?
A series circuit is a circuit with only one pathway for electrons (electricity) to flow! And a parallel circuit has two or more pathways for electrons (electricity) to flow!If you do not agree with me ask your teacher this exact question to see if i am right or wrong. If you agree with me just read the two sentences above until you have memorized it! Okay! Great!( :a thingseries circuit has a common current and a parallel circuit has a common voltage.
What voltage does a battery bank that needs 4 A to run?
It would need to be four times higher then the resistance that it is applied against. If the circuit is a 1 ohm resistor, then the voltage would need to be 4 Volts to make 4 amps.
Circuit diagram to make 4 channel RC robot car?
NO
How to wire a 4-way switch in a circuit?
To wire a 4-way switch in a circuit, you will need to connect the traveler wires from each 3-way switch to the 4-way switch. The common terminal on the 4-way switch should be connected to the light fixture. Make sure to follow the wiring diagram for the specific switch you are using.
What are the distinguishing properties that are unique to living things?
4 Things that distinguish living things from non-living things 1. Living things need space to live 2. Living things need water 3. Living things need air 4. Living things need to reproduce
How do you make a recyclable hat?
how to make a newspaper hats? 1. materials 2.newspaper 3.recycle things 4.salt tape 5.scissors This are the things that you need to know when you make a cap or a newspaper cap.
What four things are needed to complete an electric circuit?
The four elements of a complete (electrical) circuit: 1)A source of input (power supply) 2)A means of conductivity (usually wire) 3)A means by which to open and close the circuit (a switch) 4)An output device (motor, light bulb, etc)
How do I properly wire a 4 way switch in a circuit?
To properly wire a 4-way switch in a circuit, you need to connect the traveler wires from each 3-way switch to the 4-way switch terminals. The common terminal on the 4-way switch should be connected to the light fixture. Make sure to follow the wiring diagram for your specific setup to ensure proper installation.
If you have 4 things in common with a werewolf are you a werewolf?
No. If you have 4 things in common with a chimp, does that make you a chimp?
What are the 4 things that all living things need?
atr, water,food,space
What are 4 things that all living things need?
atr, water,food,space
How can I properly wire a 4-way switch in my electrical circuit?
To properly wire a 4-way switch in your electrical circuit, you will need to connect the traveler wires from each 3-way switch to the 4-way switch. The common terminal on the 4-way switch should be connected to the light fixture. Make sure to follow the wiring diagram provided with the switch and turn off the power before starting the installation.
What are 4 things living things need to survive?
1 Water 2 Food 3 Air 4 A Place to Live
