0
It would depend on the circuit diagram. In some cases, the circuit would be incomplete (simplest case is a battery with a wire attached to just one terminal).
Parallel branches that have a connection to the battery without going through other branches are independent of each other. Say you have two parallel branches and a battery. If you short circuit one of the branches, the other branch will not be affected but the battery will be (current through the battery would decrease because taking out a parallel branch increases resistance).
In short, it would depend on the circuit diagram. Note that for a nanosecond, there would be current in an open circuit, but after this brief time there would be no current flow in the segment of the circuit that has been shorted.
What else can I help you with?
What is the difference in an open circuit and a short circuit?
an open circuit is a circuit that does not complete the circle. an open circuit does not do the job as the electricity stands still a short circuit is a circuit that wires have crossed and the electricity takes the shortest path. and does not complete all of the points on the circuit
What do open and closed circuits have in common?
Both open and closed circuits involve the flow of electric current. In an open circuit, the current is interrupted or stopped due to a gap in the circuit, while in a closed circuit, the current flows continuously through a complete loop of conductor.
Why a short circuit happen?
Presumably, the current follows a path (a circuit) to do whatever it was "made" to do. If water, for instance, enters the circuit, a shorter path may develop, and the current will (partially) take the short circuit. Or a wire could become lose and short circuit the intended path.
What causes a short circuit in electrical circuits?
A short circuit in electrical circuits is caused by a direct connection between the positive and negative terminals, bypassing the normal load. This can happen due to damaged insulation, loose connections, or faulty components.
How does a short circuit work and what are its potential consequences?
A short circuit occurs when an electrical current takes an unintended path due to a direct connection between two points in a circuit with low resistance. This can lead to excessive current flow, overheating, and potentially cause fires or damage to electrical components.
What is the difference in an open circuit and a short circuit?
an open circuit is a circuit that does not complete the circle. an open circuit does not do the job as the electricity stands still a short circuit is a circuit that wires have crossed and the electricity takes the shortest path. and does not complete all of the points on the circuit
How do you find shorts and opens in an electrical circuit in multimeter?
An open circuit essentially has an infinite resistance. It is shown on digital multimeter as OL. (Open Line) A short circuit should read zero, or nearly zero, depending on the accuracy of the meter.
What are the major causes of loss of excitation on generators?
The major causes of loss of excitation on generators are due to an open circuit or a short circuit in the field winding. This may also be caused by a breakdown of the insulation system.
Can a short circuit cause low voltage?
Most likely a short circuit will cause no voltage. Due to the high current on a short circuit fault the over current protection of the circuit will trip. This will cut the voltage supply off completely.
What is an open short circuit on your ac compressor?
An open short circuit on an AC compressor refers to a failure where the electrical circuit is interrupted, preventing the compressor from receiving power. This can occur due to issues like a broken wire, a blown fuse, or a malfunctioning relay, leading to the compressor not operating at all. As a result, the cooling system may fail to function, causing inadequate or no cooling in the space being conditioned. Identifying and repairing the open circuit is essential for restoring proper AC operation.
What should you read between the commutator segments at a static condition Ohms OR short circuit?
In a static condition, the readings between commutator segments should ideally show zero volts or very low resistance, indicating that there is no significant current flowing due to an open circuit or a short circuit. If you observe a voltage reading, it could suggest a potential issue, such as a short circuit between segments. Conversely, if the resistance is too high or infinite, it might indicate an open circuit. Always ensure to compare readings against the manufacturer's specifications for accurate diagnosis.
What can cause a circuit breaker to trip?
A circuit breaker can trip due to overloading, short circuits, or ground faults.
What is the difference between an open and closed circuit in hydraulic circuit?
In an open circuit, the circuit doesn't power the load because it isn't closed fully. A closed circuit closes properly and can power the load. If you didn't know, the load is the thing your trying to power.
What is the difference between an short circuit and a closed circuit?
You know there is a differnce. The dynamic short circuit is dynamic and the static short circuit is static. It's common sense really.dyanamic means when due to some external source theresistance becomes zero ,can be through anythin due to high supply of current or anything,the current in that circiut becomes infinite and that result s in short circuiting. Static short circuit means when through the different changes in the voltage makes the resistance zero and current infinite , V = I/R WHERE R= 0 AND CURRENT BECOMES INFINIT AND THAT RESULT IN A SHORT CIRCUIT
This will flip when a circuit in a house becomes overloaded?
A circuit breaker has a small handle that will flip to the open position due to overload.
What is the resistance of a short circuit in ohms called?
Your original question was in two parts:1.) How many ohms in an open circuit? Infinite ohms (the meter will show no measurement).2.) How many ohms in a short circuit? 0 ohms. There would be no measurable ohms as there would be no resistance in the altered circuit.
What do open and closed circuits have in common?
Both open and closed circuits involve the flow of electric current. In an open circuit, the current is interrupted or stopped due to a gap in the circuit, while in a closed circuit, the current flows continuously through a complete loop of conductor.
