0
What else can I help you with?
When the two bulbs are in placewhat happens?
When two light bulbs are in place, there will be a circuit created where electricity can flow through both bulbs. If the circuit is intact and the bulbs are functioning, they will both light up. If one of the bulbs is faulty or the circuit is broken, then both bulbs may not light up.
What happens when you unscrew a light bulb in a circuit with two bulbs?
There are a few possible different results. One thing that happens in EVERY possible situation is that the bulb you unscrew is dark after you unscrew it. -- If the two bulbs are configured in either a series or a parallel arrangement and the power is off, then both bulbs are dark before you unscrew one, and nothing changes after. -- If the power is on and the two bulbs are configured in parallel, then the one you don't unscrew continues to glow after the other one is gone. -- If the power is on and the two bulbs are configured in series, then BOTH bulbs go out when you unscrew only one of them.
Can one cell in a circuit light two bulbs?
Yes, one cell in a series circuit can light up two bulbs. However, the brightness of each bulb may be reduced compared to if only one bulb were connected due to the voltage being split between the bulbs.
What is the amount of energy used in one hour by 10 100 w light bulbs?
The total energy used in one hour by 10 100W light bulbs is 1 kWh (kilowatt-hour). To calculate this, you multiply the power of each bulb by the number of bulbs and the time they are on. In this case, 100W * 10 bulbs * 1 hour = 1000 watt-hours = 1 kWh.
Will a circuit with two light bulbs in series light up?
Yes, a circuit with two light bulbs connected in series can light up. Current flows through the first light bulb, then through the second, allowing both bulbs to illuminate. If one bulb burns out, however, both bulbs will go out.
Why would your van just shut off?
It happened to my van a long time ago, after I loosened the gas tank cap, it never happened again. I guess the ventilation or gas tank cap malfunctioned so no air was let in. You can try this one. .
Is loosened a participle?
Yes, loosened is the past participle of loosen.
How do you use loosened in a sentence?
She loosened the rope from around the pole
Why does only half the strand of Christmas lights work?
Probably because you brought them cheap or the bulbs are broken.
How do you use the word loosened in a sentence?
"i loosened up my skates" or anything that can be loosened up in a statement of the past or like what i just used it in
Where can one purchase car light bulbs?
One can purchase car light bulbs from the following sources: Demon Tweaks, eBay, LED Choice, Power Bulbs, Halfords, Power Bulbs, Auto Zone, Auto Bulbs Direct.
Why must a tourniquet be loosened from time to time?
A tourniquet must be loosened only in the event of a deep laceration. When one has been applied due to amputation, it should not be loosened. Loosening a tourniquet for a laceration, blood flow can continue continue to other tissue so that an amputation does not become necessary.
Which is more efficient the fluorescent bulbs or the incandecent bulbs?
Fluorescent bulb is the more efficient one as compared to incandescent bulbs.
99' Dodge Durango What does it mean when you turn your left turn signal on it works but when you push on the brakes signal won't work?
There are two bulbs for the the front and i think the back signals. that happened to me and I went searching to find that one of the bulbs was burnt. should be easy to find.
What happened after the Reagan administration loosened regulations on savings and loan institutions S and Ls?
Many S&Ls made bad loans and went bankrupt.
Where can one buy H1 bulbs in bulk?
One can purchase H1 bulbs in bulk online on sites such as Amazon, eBay, 1000 Bulbs, Sylvania, and Buy Headlight Bulbs. One can also have them special ordered in bulk at retailers such as Auto Zone and Advanced Auto.
How do you check the potential in 230V line by using two 40w bulbs and two 60 w bulbs?
Plug the bulbs in, one by one, and check to see if they have the correct brightness.
