answersLogoWhite

0

184 - 276 ohms

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

On an 86 Toyota truck what should the pickup coil resistance be?

Distributor pickup coil resistance 140-180 ohms.


Can a Yamaha xt350 or xt600e exhaust fit the Yamaha xt400e engine?

Got a sex life but I need an exhaust.


Is there a direct correlation between increase in coil wraps and electrical resistance of a guitar pickup?

There is a direct relationship between the length of wire (thus the number of times the wire is wrapped) and the electrical resistance of the guitar pickup, measured at the two output terminals.


How do you test the glow plugs on a 1983 Mazda 2200 diesel pickup?

You can test them with an Ohm meter. Make sure all 4 have the same resistance or if no resistance then you've found the bad one(s).


What are the best features to consider when choosing a pickup truck tent for camping?

When choosing a pickup truck tent for camping, consider features like size to fit your truck bed, ease of setup, weather resistance, ventilation, and durability.


How do you test a pick up module in a 302 distributor?

To test a pickup module in a Ford 302 distributor, first disconnect the distributor from the ignition system. Use a multimeter to check the resistance across the pickup's terminals; it should typically read between 500 to 1,500 ohms. If the resistance is outside this range, the pickup may be faulty. Additionally, you can test the signal output while cranking the engine with an oscilloscope to ensure it produces a square wave signal.


How do you test a pickup coil on a Yamaha v star classic 650?

To test the pickup coil on a Yamaha V Star Classic 650, first, ensure the motorcycle is off and disconnected from the battery. Use a multimeter set to the ohm (Ω) setting, and measure the resistance across the pickup coil terminals; it should typically be between 200-400 ohms. If the reading is significantly outside this range or shows infinite resistance, the pickup coil is likely faulty and should be replaced. Additionally, you can check for proper signal output while cranking the engine to confirm functionality.


On a 77 GMC 350 HEI system with a new pickup coil why can you get no reading for resistance between either wire and ground What could cause this you can get resistance readings everywhere else?

The resistance to ground should be infinite, becouse its an isolated circuit. Any resistance to ground less than infinity would mean there is a short to ground.


How do you get frugooscape codes when it can not be searched?

you wont need 2 serch any more cuz here they are. Frugooscape cheats ::newstuff0 ::newstuff1 ::newstuff2 ::pickup 6739 1 ::pickup 1050 1 ::pickup 2665 1 ::pickup 2661 1 ::pickup 2663 1 ::pickup 2667 1 ::pickup 7962 1 ::pickup 3686 1 ::pickup 3481 1 ::pickup 3483 1 ::pickup 3488 1 ::pickup 2627 1 ::pickup 2653 1 ::pickup 2655 1 ::pickup 2659 1 ::pickup 2673 1 ::pickup 5001 1 ::pickup 2669 1 ::pickup 2671 1 ::pickup 2675 1::pickup 2619 1::pickup 2615 1::pickup 2617 1::pickup 2621 1::pickup 385 1::Pickup 395 1::pickup 558 1::pickup 560 1::pickup 562 1::pickup 567 1::pickup 555 1::pickup 554 1::pickup 563 1::pickup 559 1::pickup 561 1::pickup 566 1::pickup 564 1 you wont need 2 serch any more cuz here they are. Frugooscape cheats ::newstuff0 ::newstuff1 ::newstuff2 ::pickup 6739 1 ::pickup 1050 1 ::pickup 2665 1 ::pickup 2661 1 ::pickup 2663 1 ::pickup 2667 1 ::pickup 7962 1 ::pickup 3686 1 ::pickup 3481 1 ::pickup 3483 1 ::pickup 3488 1 ::pickup 2627 1 ::pickup 2653 1 ::pickup 2655 1 ::pickup 2659 1 ::pickup 2673 1 ::pickup 5001 1 ::pickup 2669 1 ::pickup 2671 1 ::pickup 2675 1::pickup 2619 1::pickup 2615 1::pickup 2617 1::pickup 2621 1::pickup 385 1::Pickup 395 1::pickup 558 1::pickup 560 1::pickup 562 1::pickup 567 1::pickup 555 1::pickup 554 1::pickup 563 1::pickup 559 1::pickup 561 1::pickup 566 1::pickup 564 1


How do you test a pickup coil for a 1994 gmc Yukon 5.7?

To test the pickup coil on a 1994 GMC Yukon 5.7, first disconnect the wiring harness from the distributor. Use a multimeter to measure the resistance across the pickup coil terminals; it should typically read between 500 to 1500 ohms. If the reading is outside this range or shows an open circuit, the pickup coil is likely faulty and should be replaced. Additionally, you can check for voltage while cranking the engine; no signal may indicate a bad pickup coil.


What is meant by hot pick-ups?

A "hot" pickup is generally over wound and has a high resistance as measured in Ohms. In laymens terms it means it is louder than average pickups.


How do you get rid of ground loop from a turntable?

If you mean you want to get rid of some background "hum" that is being picked-up by the signal leads from the pickup cartridge - probably from the turntable's motor - you should check the pickup's signal wiring is shielded and grounded. Usually turntables already have shielded wiring for the pickup leads so it is worth checking that none of the shielded wires have become disconnected from the Ground terminal on the turntable's baseboard or from the pickup head itself. Next check that your turntable's Ground terminal is actually connected to the Ground terminal at the back of your preamp or amp. Sometimes there is a separate Grounding wire or sometimes it is just the shield of the pickup signal wiring that does this job. Be sure to unplug everything - amp, preamp and turntable - from the household AC supply socket outlet before you do any checks. It is best to use the resistance measurement setting of a normal electrical test meter to do those ground wiring checks. The resistance measurements from turntable Ground terminal to pickup housing and from that same terminal to the amp's Ground terminal should show a very low resistance, almost zero Ohms.