0
The supply to the field winding is derived through no voltage coil. So when field current flows, the NVC is magnetized. Now when the handle is in the 'RUN' position, soft iron piece connected to the handle and gets attracted by the magnetic force produced by NVC, because of flow of electric current through it.
What else can I help you with?
What is the process to integrate this function over the area of the coil in order to find the flux?
To find the flux of a coil, you need to integrate the function over the area of the coil. This involves calculating the total amount of the function passing through the coil's surface.
In order for an air-conditioning coil to remove moisture from the air it must be below the - temperature of the air?
In order to remove moisture from the air, the air-conditioning coil must be below the dew point temperature of the air. This allows the coil to cool the air below its dew point, causing water vapor to condense and be removed.
What would happen to the coil if the current passing through it was too large?
If the current passing through the coil is too large, it can cause the coil to overheat and possibly burn out. This can damage the insulation on the wire and affect the coil's performance. It may also lead to a magnetic field that is too strong, affecting the intended function of the coil.
What is the basis of the function of a galvanometer?
The function of a galvanometer is based on the interaction between a magnetic field and an electric current passing through a coil of wire. When a current flows through the coil, it creates a magnetic field that interacts with a permanent magnet, causing a deflection of the needle on the galvanometer scale.
What is the function of thermo stateic expention volve?
The function of a thermostatic expansion valve is to control the flow of refrigerant into the evaporator coil of an air conditioning or refrigeration system. It regulates the amount of refrigerant entering the coil based on the temperature and pressure conditions, ensuring efficient cooling and proper system operation.
What is the use of 4-point starter in motors?
The four-point starter eliminates the drawback of the three-point starter. In addition to the same three points that were in use with the three-point starter, the other side of the line, L1, is the fourth point brought to the starter when the arm is moved from the "Off" position. The coil of the holding magnet is connected across the line. The holding magnet and starting resistors function identical as in the three-point starter. * The possibility of accidentally opening the field circuit is quite remote. The four-point starter provides the no-voltage protection to the motor. If the power fails, the motor is disconnected from the line.
What is the function of an overload release coil?
it is used to protect the motor
Where on a Monte Carlo is the starter coil?
it is mounted to the starter !
What is the function of no volt release in 3 point starter?
The supply to the field winding is derived through no voltage coil. So when field current flows, the NVC is magnetized. Now when the handle is in the 'RUN' position, soft iron piece connected to the handle and gets attracted by the magnetic force produced by NVC, because of flow of electric current through it.
Does a coil boot up the starter motor?
no
What device has a coil armature and heaters?
A motor starter.
What is the problem when a truck starts some times and not others?
Might be you starter or starter rely and/or coil.
I am trying to put a remote starter in my 2003 Rav4 and I can't find the coil ---- Where is it --- Also is the high votage coil starter the same as the high coil?
02 to 04 RAV's got individual computer controlled coils your remote starter has to conected to the ignition assembly in the steering cullum.
What is the process to integrate this function over the area of the coil in order to find the flux?
To find the flux of a coil, you need to integrate the function over the area of the coil. This involves calculating the total amount of the function passing through the coil's surface.
Your 94 Jeep Cherokee has no power going to the coil what would cause this?
bad starter or starter solenoid.
Why is it that a 1989 Honda Accord Starts up but when the key is let go it shuts off As long as the key is held in Run the car does not shut off What can cause this?
Check the ignition switch and the coil resistor if the Honda has one. When the starter is engaged there is a direct connection to the coil. The intention is to give the coil a little more voltage when the starter is engaged. If the ignition switch isn't connecting properly you won't run when you release the starter. If your vehicle uses a coil resistor you might get the same results. That's just a couple possibilities, good luck.
How relay is used to control induction motor?
If you want to control induction motor using a control relay give neutral directly to the one point of coil of relay & one point of coil of contactor then give control supply through push button to second point of coil of relay. use one NO point of relay and give supply to coil of contactor. and also use one NO of contactor for holding the contactor & take OFF (NC) in the starting to stop motor after complition of work. It is jut like an Direct On-line starter.
