answersLogoWhite

0

The millivolt range of a gas valve is typically around 250 to 750 millivolts. This low voltage is generated by a thermocouple or a thermopile and is used to open and close the gas valve to control the flow of gas.

User Avatar

AnswerBot

1y ago

What else can I help you with?

Continue Learning about Physics

How do millivolt gas valves work?

A millivolt gas valve is used in a standing pilot type of appliance. In a normal application there are actually 2 valves in one. one valve controls gas flow to the pilot and the other part of the valve controls gas flow to the burner. The pilot burns on a device or devices that produce a small amount of electricity ( millivoltage ) some valves accomplish this with a thermopile producing energy for the pilot and the burner portions of the valve. others use a thermocouple to produce energy to keep the pilot open and a thermopile to produce the energy for the burner side of the valve. In a typical gas fireplace valve the pilot runs on 30mV ( millivolts ) and the burner runs on 500 mV. it sounds like alot but it's only .5volts. This energy creates an electromagnet that pulls the valve open against a spring. That is the fail safe and how the pilot safety function works, if for any reason the energy isn't present, the spring snaps the valve shut shutting off the gas. Millivolt valves are NOT field serviceable. They should never be disassembled as they will leak. Most issues with millivolt valves are caused by a simple lack of manufacturer recommended service and maintenance.


One millivolt is how much larger than one microvolt?

One millivolt is 1000 times larger than one microvolt.


Would a bad millivolt thermopile keep the pilot light in a floor furnace from staying lit?

Yes, a bad millivolt thermopile can cause the pilot light in a floor furnace to go out or not stay lit. The thermopile generates the voltage needed to keep the gas valve open and maintain the pilot light, so if it is faulty, the pilot light may not stay lit consistently.


How does adjusting the gas needle valve on the Bunsen burner affect the flame?

Adjusting the gas needle valve controls the flow rate of gas entering the burner. Decreasing the gas flow by turning the needle valve counterclockwise results in a smaller, bluer flame with less heat, while increasing the gas flow by turning the needle valve clockwise produces a larger, yellower flame with more heat.


Why is it necessary to turn off the gas with the gas cock rather than with the valve on the burner?

When you leave the gas cock open when you turn off the burner valve, and someone moves the burner to another gas port, there would be a serious gas leak until you turned off the gas at the gas cock.

Related Questions

How do you test a millivolt gas valve?

You can test a millivolt gas valve with a multimeter by measuring voltage across the valve terminals while the gas valve is energized. The reading should be in the range of 500-750 millivolts to indicate that the valve is operating correctly. Additionally, you can visually inspect the valve for any signs of physical damage or corrosion.


Why doesn't my hot water heater light everytime?

If it is gas operated, the hot water heater may not light because it may have a defective millivolt sensor. The millivolt sensor is heated up by the pilot and generates a fractional amount of voltage telling the gas valve that the pilot is lit and the gas valve can now be safely opened to heat the water heater.


How do millivolt gas valves work?

A millivolt gas valve is used in a standing pilot type of appliance. In a normal application there are actually 2 valves in one. one valve controls gas flow to the pilot and the other part of the valve controls gas flow to the burner. The pilot burns on a device or devices that produce a small amount of electricity ( millivoltage ) some valves accomplish this with a thermopile producing energy for the pilot and the burner portions of the valve. others use a thermocouple to produce energy to keep the pilot open and a thermopile to produce the energy for the burner side of the valve. In a typical gas fireplace valve the pilot runs on 30mV ( millivolts ) and the burner runs on 500 mV. it sounds like alot but it's only .5volts. This energy creates an electromagnet that pulls the valve open against a spring. That is the fail safe and how the pilot safety function works, if for any reason the energy isn't present, the spring snaps the valve shut shutting off the gas. Millivolt valves are NOT field serviceable. They should never be disassembled as they will leak. Most issues with millivolt valves are caused by a simple lack of manufacturer recommended service and maintenance.


How millivolt switch works?

I am assuming that you mean switching a millivolt gas value. The switch applies a voltage to the gas valve thus allowing gas to flow. The voltage is provided by a thermopile. This device transforms the heat from the pilot into a voltage that can be used to control the valve. This system does not require an external voltage source. It does require the pilot to continuously operate. A thermopile consists of a number of thermocouples that are wired in series. This allows an increase in the voltage that would be provided by a single thermocouple.


Can you improve voltage level in the range of millivolt into a 15volt?

A voltage amplifier (high input and output impedances) with a gain of 83.5 dB will amplify a signal of 1 millivolt to an output of 15 volts.


Does the safety valve on a gas range opens when the thermocouple detects no pilot flame?

yes


How can I Convert a restaurant U.S. Range oven from gas to propane?

In order to convert a gas range to propane, one must change the inlet valve. There flow rate of the gas must also be adjusted too.


Is the gas valve in the on position?

Is the gas valve turned on?


Is the gas valve open or closed?

The gas valve is closed.


What is a thousandth of a volt?

A milliVolt.


What is an redundant gas valve.?

A redundant gas valve is a safety feature in a gas system where two valves are installed in series to ensure that gas flow can be shut off if one valve fails. This redundancy helps prevent gas leaks and potential hazards.


Is the gas valve in the on or off position?

The gas valve is currently in the off position.