uncoil or unloop
(The opposite of a coiled path is a straight or flat path.)
Yes, both sides of a coil typically have electrical flow. In a coil, current flows in one direction on one side of the coil and in the opposite direction on the other side, creating a magnetic field.
Having a controlling couple in a moving coil galvanometer is essential to ensure the coil comes back to its original position after deflection. This controlling couple helps to stabilize the movement of the coil and maintain the accuracy of the measurements taken by the galvanometer. Without it, the coil may continue to oscillate or not return to its resting position, leading to inaccurate readings.
Yes, a corkscrew is a type of screw specifically designed to remove corks from bottles, typically wine bottles. It has a helical coil that allows it to twist into the cork and then pull it out when turned in the opposite direction.
Moving the magnet towards the coil induces a current in one direction, while moving it away induces a current in the opposite direction. This is due to Faraday's law of electromagnetic induction, which states that a changing magnetic field induces an electromotive force (EMF) that leads to the current flow.
One way you can write it is : She had to coil it around to activate it.Or you could say: I had to coil it for a project.
Yes, both sides of a coil typically have electrical flow. In a coil, current flows in one direction on one side of the coil and in the opposite direction on the other side, creating a magnetic field.
opposite end of the spark plug wire from the spark plugs
The purpose of the permanent magnet in the moving coil meter is to measure electrical current. The coil will have a magnetic field which will react to the magnetic field of the permanent magnet. Since opposite poles attract, it will cause for the coil to move.Ê
make sure the coil is a positive grounded coil, most are negative ground. battery just hooks up opposite to usual the coil is the only thing u need to make sure of
Under the dizzy cap, a black square opposite the coil, it has 3 wires
Having a controlling couple in a moving coil galvanometer is essential to ensure the coil comes back to its original position after deflection. This controlling couple helps to stabilize the movement of the coil and maintain the accuracy of the measurements taken by the galvanometer. Without it, the coil may continue to oscillate or not return to its resting position, leading to inaccurate readings.
if it is a capacitor start and run motor, this is because of shorted capacitor
EMF is the voltage across a coil (or motor) due to changes in the magnetic field. If you change the current the coil will generate a voltage (in the opposite direction of the current). So it is not the field but the change that matters.
-- While the magnet is moving, there is a voltage between the ends of the coil and, if there's any connection between the ends, then there's a current in the coil. -- When the magnet stops moving, all of that goes away. -- When the magnet is pulled out, it all happens again, but with the opposite polarity.
By 'adding electric currents', you are presumably talking about passing a d.c. current through a coil wound around a magnet?First of all, you cannot increase the flux density of a magnet beyond saturation, regardless of the current or number of turns that make up the coil. Whether on not you increase or reduce the flux density depends on the polarity of the coil compared with the polarity of the magnet; if they are opposite then, yes, you can demagnetise the magnet and, in fact, remagnetise it in the opposite direction.
Different ways to induce current in a coil are as given below:(1) If a magnetic field is changed round a coil then an induced current is set up in the coil. It can be done by taking a bar magnet and bringing it closer to the coil or taking it away from the coil.(2) If a coil is moved in a magnetic field, then again an induced current is set up in the coil.(3) If a coil is rotated in a uniform magnetic field, it may also cause an induced current in the coil.(4) If we take two coils and insert them over a non conducting cylindrical roll then on changing current flowing in one coil, an induced current is obtained in the other coil.CommentYou don't induce a 'current' into a coil; you induce a voltage. If that coil is open circuited, then no current will flow. If, on the other hand, the coil is connected to a load, or its opposite ends short-circuited, then the induced voltage will cause a current to flow. Remember, current will only flow if there is a load, or short circuit, and the value of the current will depend upon the value of the induced voltage and the resistance of the load or short circuit.
Lacuna coil