0
What else can I help you with?
What is the difference between HVAC diffuser's neck velocity and face velocity?
In HVAC terminology, a diffuser's neck velocity is defined as the velocity of air traveling through the duct work to the air outlet or inlet. The difference of the face velocity is this is a measurement of fume hood performance.
What is face velocity?
Face velocity is a measure of the speed at which air moves across the face of a hood, such as in a laboratory fume hood. It is typically expressed in units of feet per minute (fpm) and ensures that airborne contaminants are effectively captured and contained within the hood. Maintaining the appropriate face velocity is crucial for proper hood performance and worker safety.
What is formula for converting face velocity into cubic feet per minute?
You need to know the area of the pipe or duct. If you have that area, in square feet, V = Q/A where V = velocity (ft/minute in this case), Q = flowrate (cubic feet/minute in ths case), and A = area (square feet in this case). Then, you just have to apply conversions to get whatever units you want to present or use the answer in.
What is face velocity of air?
Face velocity of air is defined as the speed at which air moves across the opening of a supply or exhaust outlet, usually measured in feet per minute (fpm). It is an important parameter in ventilation systems to ensure that air is distributed properly and contaminants are removed effectively. High face velocities can lead to excessive noise and pressure drops, while low face velocities may result in poor air distribution.
What are some common challenges students face when solving angular projectile motion problems?
Some common challenges students face when solving angular projectile motion problems include understanding the relationship between angle and velocity, applying trigonometry to calculate components of velocity, and accounting for factors like air resistance and initial height.
If the coil face velocity is 500fpm with a 14fins inch find the number of rows for the coil?
hi dear , the number of rows for this coil is 6 rows , but there is another factor , u have to take in cosideration the capacity ( BTU ) , thanks
What is the difference between HVAC diffuser's neck velocity and face velocity?
In HVAC terminology, a diffuser's neck velocity is defined as the velocity of air traveling through the duct work to the air outlet or inlet. The difference of the face velocity is this is a measurement of fume hood performance.
What is face velocity?
Face velocity is a measure of the speed at which air moves across the face of a hood, such as in a laboratory fume hood. It is typically expressed in units of feet per minute (fpm) and ensures that airborne contaminants are effectively captured and contained within the hood. Maintaining the appropriate face velocity is crucial for proper hood performance and worker safety.
Is face bleaching recommended?
No, but try it!
How can you get sacked?
Slap your boss in the face, but not recommended.
How do you clean egniton coil on Briggs and stratton engine?
Remove the shrouds then you can do it in two ways .If the coil is already set right you can pull the fly wheel and sand or wire brush the face of the coil .You can remove the coil and leave the fly wheel in place.You will have to pull the spark wire off the spark plug ,remove the bolts holding the coil in place (move the magnet so it is away from in front of the coil first) ,lift coil remove wire off spade connector .Then you can clean the coil with a wire brush or sand paper (you need to clean the face and the fly wheel face and make sure you wipe so no dirt is left) the you reverse the removal and reset the coil if you have a manual it will give you proper coil gap. If not you can use a thick peace of paper to gap it.
What rule is applied to find the polarity of the face of a current carrying circular coil?
in physics
What is formula for converting face velocity into cubic feet per minute?
You need to know the area of the pipe or duct. If you have that area, in square feet, V = Q/A where V = velocity (ft/minute in this case), Q = flowrate (cubic feet/minute in ths case), and A = area (square feet in this case). Then, you just have to apply conversions to get whatever units you want to present or use the answer in.
Face velocity through sand trap louvers?
.Sand Trap louvers and types of louvers
Why cooling has a greater effect in a dry dessert than in the humid tropics?
because of ur face
Is it safe or recommended to blow in a baby's face for any reason"?
Blowing in a baby's face is not safe or recommended as it can startle or upset the baby and may also introduce germs or bacteria into their respiratory system. It is best to avoid blowing in a baby's face for any reason.
Can you take face masks on a plane?
Yes, you can take face masks on a plane. It is recommended to wear a face mask during the flight for your safety and the safety of others.
