0
To replace the string on a Ryobi Expand-It weed wacker, follow these steps:
- Turn off the weed wacker and disconnect the spark plug to ensure safety.
- Remove the spool housing by pressing the tabs on the sides and pulling it off.
- Take out the old string spool and replace it with a new one, making sure to follow the directional arrows for winding the string.
- Feed the string through the eyelet holes on the spool housing.
- Reattach the spool housing and reconnect the spark plug.
- Test the weed wacker to ensure the string is working properly.
What else can I help you with?
How do you string a Ryobi weed wacker?
To string a Ryobi weed wacker, first remove the spool cover and old string. Then, insert the new string through the holes in the spool and wind it in the direction indicated on the spool. Finally, replace the spool cover and trim any excess string.
How do I perform a Ryobi weed wacker string replacement?
To perform a Ryobi weed wacker string replacement, first turn off the weed wacker and disconnect the spark plug. Then, remove the spool housing and take out the old string. Cut a new piece of string to the correct length and thread it through the spool. Wind the string evenly onto the spool and reassemble the housing. Finally, reconnect the spark plug and test the weed wacker.
How do I string a Ryobi weed wacker?
To string a Ryobi weed wacker, first, turn off the engine and disconnect the spark plug. Then, remove the spool cover and take out the old string. Cut a new piece of string to the appropriate length and insert it into the spool, following the arrows for the correct winding direction. Finally, reassemble the spool cover and reconnect the spark plug before starting the weed wacker.
How can I replace a line in a Ryobi weed wacker?
To replace a line in a Ryobi weed wacker, first, remove the spool cover and take out the old line. Cut a new line to the appropriate length and insert it into the spool. Wind the line evenly and securely, then reassemble the spool cover.
How do I replace the string on a Ryobi 40 volt trimmer?
To replace the string on a Ryobi 40-volt trimmer, first, remove the spool cover and old string. Then, wind the new string onto the spool following the arrows for the correct direction. Finally, reassemble the trimmer and trim the excess string.
How do I replace the string on my Ryobi string trimmer?
To replace the string on your Ryobi string trimmer, first turn off the trimmer and disconnect the spark plug. Then, remove the spool housing and take out the old string. Cut a new piece of string to the appropriate length and feed it through the trimmer head. Wind the string in the direction indicated on the spool and secure the ends. Finally, reassemble the trimmer and test it before use.
What size of string for RYOBI cs26?
the ryobi owners manual calls for a .095
How can I restring a Ryobi weed wacker?
To restring a Ryobi weed wacker, first, remove the spool from the trimmer head. Cut a length of new trimmer line, usually around 10 feet. Insert one end of the line into the hole in the spool and wind it in the direction indicated on the spool until it is full. Reattach the spool to the trimmer head and feed the line through the eyelets. Your Ryobi weed wacker is now restrung and ready to use.
How do I restring a Ryobi weed wacker?
To restring a Ryobi weed wacker, first remove the spool from the trimmer head. Cut a length of new trimmer line, usually around 10 feet. Insert the line into the spool following the arrows for direction. Wind the line evenly and tightly around the spool. Reattach the spool to the trimmer head and feed the line through the eyelets. Your Ryobi weed wacker is now restrung and ready to use.
How do I properly install the Ryobi weed wacker line?
To properly install the Ryobi weed wacker line, first, turn off the weed wacker and disconnect the spark plug. Then, remove the spool cover and take out the old line. Cut a new line to the correct length and insert it into the spool, following the arrows for the correct winding direction. Finally, reassemble the spool cover and reconnect the spark plug before using the weed wacker.
How do you wind a Ryobi weed wacker spool?
To wind a Ryobi weed wacker spool, first remove the spool from the trimmer. Then, wind the trimmer line around the spool in the direction indicated on the spool. Make sure to evenly distribute the line and avoid overlapping. Finally, reattach the spool to the trimmer and you're ready to use it.
How do you refill a Ryobi string trimmer?
To refill a Ryobi string trimmer, you need to first turn off the trimmer and remove the spool cap. Then, take out the empty spool and replace it with a new one, making sure to wind the trimmer line in the correct direction. Finally, reattach the spool cap and you're ready to trim again.
