0
9/5/2012
Remove the plastic trigger that goes around the trimmer, by going to the open side and spreading it and sliding it off. Now you will see into each hole the white switch that is stopped by a dark plastic guard. Compress the two plastic guards,I did it with two screwdrivers, and had my wife pull on the clipperhead. That pulls the body of the trimmer out. The battery has clips on each end and has to be pried up, while holding the battery holder in place. The batteries are on ebay at $18.00 with the clips,or you can buy a battery local with prongs on each end and soder them in.
Vince
What else can I help you with?
How can I replace the trimmer line on my Ryobi cordless trimmer?
To replace the trimmer line on your Ryobi cordless trimmer, follow these steps: Turn off the trimmer and disconnect the battery. Remove the spool cover by pressing the tabs on the sides and pulling it off. Take out the spool and remove any remaining old line. Cut a new piece of trimmer line to the appropriate length. Insert the line into the spool, following the arrows for the correct winding direction. Reassemble the spool and spool cover, then reconnect the battery and turn on the trimmer.
How do you replace line on task force trimmer 21083?
To replace the line on a Task Force trimmer model 21083, first, ensure the trimmer is unplugged or the battery is removed for safety. Locate the spool on the trimmer head, then press the tabs to release it. Remove any old line and feed new line (typically 0.065-inch diameter) into the spool, following the directional arrows for proper winding. Finally, reattach the spool to the trimmer head and ensure it clicks securely into place.
How can I replace the trimmer head on my Ryobi Expand-It trimmer?
To replace the trimmer head on your Ryobi Expand-It trimmer, first, remove the old trimmer head by unscrewing it. Then, attach the new trimmer head by screwing it on securely. Make sure to follow the manufacturer's instructions for proper installation.
When was Jon Trimmer born?
Jon Trimmer was born on September 18, 1940, in Petone, New Zealand.
How do you replace line on e61511 line trimmer?
To replace the line on an E61511 line trimmer, first, ensure the trimmer is unplugged or the battery is removed for safety. Locate the spool on the trimmer head and remove it by pressing the tabs or unscrewing it, depending on the model. Remove the old line and wind the new line onto the spool according to the direction indicated, leaving equal lengths on both sides. Finally, reattach the spool to the trimmer head, making sure the line is properly threaded through the eyelets before use.
What is the best method for replacing the weed trimmer line on a string trimmer?
To replace the weed trimmer line on a string trimmer, follow these steps: Turn off the trimmer and disconnect the power source. Remove the spool housing by pressing the tabs or unscrewing the cap. Take out the old line and cut a new piece to the appropriate length. Insert the new line into the trimmer head following the arrows for the correct direction. Reassemble the spool housing and test the trimmer.
How can I replace trimmer line using the bump feed mechanism?
To replace trimmer line using the bump feed mechanism, follow these steps: Turn off the trimmer and disconnect it from the power source. Locate the bump feed knob on the trimmer head. Press the tabs on the sides of the trimmer head to remove the spool. Remove any remaining old trimmer line from the spool. Cut a new piece of trimmer line to the appropriate length. Insert the new trimmer line into the spool, following the arrows indicating the winding direction. Place the spool back into the trimmer head and secure it by pressing until it clicks into place. Test the trimmer to ensure the new line feeds properly when bumping the head on the ground.
How do you replace head on yardmaster weed trimmer?
To replace the head on a Yardmaster weed trimmer, first ensure the trimmer is turned off and unplugged or the battery is removed for safety. Locate the release button or tabs on the trimmer head, then press or squeeze them to detach the old head. Align the new head with the mounting shaft and push or twist it into place until it clicks securely. Finally, reassemble any protective covers and ensure everything is tightened before use.
How do I perform a Ryobi trimmer string replacement?
To perform a Ryobi trimmer string replacement, first turn off the trimmer and disconnect the spark plug. Remove the spool cover and take out the old string spool. Cut a new piece of trimmer line to the appropriate length and insert it into the spool. Wind the new line evenly onto the spool in the direction indicated on the spool. Reassemble the trimmer and test the new string before use.
How can I extend the string on a Ryobi trimmer?
To extend the string on a Ryobi trimmer, you need to follow these steps: Turn off the trimmer and disconnect it from the power source. Locate the trimmer head and remove the spool cover. Take out the old string and cut a new piece to the appropriate length. Insert the new string into the trimmer head following the arrows for the correct direction. Wind the string evenly and securely onto the spool. Reassemble the trimmer head and spool cover. Test the trimmer to ensure the string is working properly.
How do You restring a Honda weed trimmer?
You remove the bottom cover off the weed trimmer, and remove the tangled old wire. Insert the new wire into the side of the trimmer and wrap it around the black spindle.
How can I restring a Ryobi string trimmer?
To restring a Ryobi string trimmer, first remove the spool from the trimmer head. Cut a length of new trimmer line, thread it through the holes in the spool, and wind it evenly around the spool. Reinsert the spool into the trimmer head, and feed the line through the trimmer head eyelets. Finally, secure the spool back in place and trim any excess line.
