Cleaning

I have done this for years and it works great...but it is VERY STRONG fumes!!! But does the trick and is not caustic. I have redone on blouses a few times and still no holes.

It has to be CHLORINE-FREE bleach. The active component of regular bleach is sodium hypochlorite, which reacts with ammonia to form hydrazine, which is a very toxic gas (NaOCl + 2 NH3 --> N2H4 + NaCl + H2O). There are also several side reactions that also produce other toxic gases. Chlorine-free bleach is usually hydrogen peroxide, but ammonia's reaction with H2O2 creates nitric oxide (also toxic) and nitrogen gas, but household H2O2 is usually very weak. I'd still be very careful and have plenty of ventilation.

Disadvantages include the costliness, and the dangers of being exposed to the solvents.

To get rid of stains in clothes, start by treating the stain as soon as possible with a pre-treatment or stain remover. Then, wash the clothing in the hottest water suitable for the fabric. If the stain persists, repeat the treatment before drying the clothing.

To remove chalk stains from a fabric chair, you can first try gently scraping off any dried chalk with a blunt edge, then blot the area with a cloth dampened with a mixture of water and mild detergent. If the stain persists, you can try using a fabric stain remover according to the product's instructions. Always test on a small, inconspicuous area first to make sure it doesn't damage the fabric.

To clean Liquid Nails off a surface, you can use a solvent like rubbing alcohol or acetone to soften the adhesive. Apply the solvent to a cloth and gently rub the area until the adhesive starts to loosen. Use a plastic scraper to remove the softened adhesive, being careful not to damage the surface. Repeat as needed until the adhesive is completely removed.

Yes, you can try using a small amount of rubbing alcohol or vinegar on a cloth to gently wipe the affected area of the wood floor. Make sure to test in a small, inconspicuous area first to ensure it does not damage the wood finish. If the spill is extensive or the wood finish is sensitive, professional help may be needed.

Soap is sodium or potassium salts of fatty acids, and these days is usually used only for cleaning human skin, but in the past was used for many other cleaning purposes.

Detergent is a substance used for cleaning, so soap is a type of detergent. Detergents are often surfactants (as is soap), which help to dissolve oils in water, useful in cleaning dirty dishes or greasy skin.

Both detergent and soap can be harmful to skin (but are not always), and neither form kill or remove 100% of bacteria.

Put them in the washing machine on a gentle COLD wash. A hot wash can melt and take apart the seams on converse.. W/ specific stains Vanish or another stain removal soap / spray can help to remove if they are stubborn stains.

It is a good idea to put the shoes inside an old pillow case and maybe stick a towel or two in the wash so they don't hit off the washing machine too much and get damaged.

For the laces, take them out and just soak them in bleach and hand wash them.

This is how I've cleaned mine.

If it is WHITE put Hydrogen Peroxide on it and then bleach it, but if its not put Hydrogen peroxide then cold water, then just throw it in the wash with cold water, it has always worked for me.

whatever you use be careful not to remover the lacquer the best thing to use is super strength nail polish remover that contains acetone I glued a piece of carpet to my bathroom floor without removing the vinyl first when I ripped up the carpet it left the glue on the floor and I went to the chemist to buy nail polish remover that contained acetone and that work great just the job it also removes stupid glue-(Super Glue)

To remove tar from denim pants, you can place the affected area in the freezer to harden the tar, then scrape it off with a blunt tool like a butter knife. Next, apply a stain remover or a mix of dish soap and warm water to the spot, and launder the pants as usual. Repeat if necessary until the tar is fully removed.

To remove ink stains from clothes, you can try using rubbing alcohol or a mixture of dish soap and hydrogen peroxide. Dab the stain with the solution, then rinse with cold water. Repeat as needed before laundering as usual.

To remove candle wax from a mirror, first freeze the wax with an ice pack or ice cube in a plastic bag to harden it. Then gently scrape off the hardened wax using a plastic card or a blunt knife. Finally, wipe the area with a cloth dampened with warm, soapy water to remove any residue.

Yes, hydrochloric acid can be used to clean mortar from brick walls, but it should be used with caution. It is a strong acidic solution that can effectively dissolve mortar residue, but it can also damage the brick surface if not used properly. It is important to follow safety precautions and test a small area first before applying it to the entire surface.

To clean limestone tiles in a shower, you can use a mixture of mild dish soap and warm water. Avoid harsh chemicals that can damage the limestone surface. Rinse thoroughly with clean water after cleaning to prevent residue buildup.

Silly Putty is made primarily of silicone polymers along with other ingredients such as boric acid and coloring agents. Silicones give it its unique properties, allowing it to be stretchy and moldable.

Platinum over sterling silver rings are less likely to tarnish compared to regular sterling silver, as platinum is a tarnish-resistant metal. However, over time, the sterling silver base may still tarnish slightly depending on factors like environment and care. Regular cleaning and maintenance can help minimize tarnishing.

You can try using rubbing alcohol or a commercial stain remover specifically designed for upholstery. Test on a hidden area first to ensure it doesn't damage the fabric. Blot the stained area with a clean cloth and repeat until the stain is gone.

First of all the shirt needs to be already washed. Yes you will have to wash it again even though it is already. First off put your washer machine on hot water and make it to where it is a super/very large load. Just put your shirt ONLY in. Wash any cycle you wish. Once done put it in the dryer on high heat for about 45-60 minutes. When done drying take it out and there you go.

PS- If you do this process and your shirt still doesnt fit. Put it in the dryer on low heat and keep checking until it is warm. Then put in on high heat for 30 minutes.

To remove dry erase marker from a chalkboard, you can try using a damp cloth or paper towel to wipe it off. If that doesn't work, you can use a chalkboard eraser or a Magic Eraser to gently scrub the marker off. Be sure to dry the board thoroughly after cleaning.

Putting dish soap in the dishwasher can cause excessive sudsing and leaks due to the dishwasher being designed to work with specially formulated dishwasher detergent. The suds can overflow, leading to a mess in your kitchen. It's best to use detergent specifically made for dishwashers to ensure efficient and effective cleaning.

Bluing agents used in laundry are synthetic compounds designed to counteract the yellow tint caused by some detergents on white fabrics. These agents are typically made in a laboratory using various chemicals and are not naturally occurring.

You can usually remove deodorant buildup from your underarms by exfoliating with a gentle scrub or using a mixture of baking soda and water to gently scrub the area. You can also try using a mixture of vinegar and water to break down the buildup before washing it off with soap and water. Avoid harsh scrubbing or using abrasive materials to prevent irritation.

The response will be incumbent on the circumstances. But essentially they will "contain and neutralize." Meaning after the scene has been secured, the release is prevented from migrating any further than possible. Let's focus on a liquid spill. Property and lives are protected first, and then consideration is given to sewerage and drainage into rivers and streams. Sometimes the material can "stabilized" in situ, meaning it can be converted from a liquid to a foam or gel. Then having contained the release, crews will neutralize and gather up the material for proper disposal. The response is known as a dynamic response, since although there are specific guidelines, every response is different and must be treated according to circumstances. Another respondant has provided the following general guidelines: Step 1 - Get Away

If a hazardous spill is discovered employees should move a safe distance away. Turn off ignition

sources and equipment if possible.

Step 2 - Identify what you saw

Accurately describe what you have just seen. What was it? Was it a solid, liquid or gas? Where

was it? Was it raining? Did it have a familiar odour?

Step 3 - Get Help

Follow company procedures. Notify the key contact immediately and report the details of the spill.

Step 4 - Hazard assessment

Determine the hazards by obtaining the Material Safety Data Sheets, read labels, identifying signs

or Transportation of Dangerous Goods placards. If this becomes necessary responders should

assume the worst and use the highest level of personal protection equipment.

Step 5 - Alert others and evacuate unnecessary personnel

Step 6 - Secure the area and establish spill boundary

Step 7 - Prepare a plan of action

After the hazard has been identified, the team should prepare an action plan. They should

consider environmental conditions such as wind direction, potential for rain, what might happen on

site. Prepare for emergency vehicle access.

Step 8 - Secure proper equipment and materials

Establish levels of personal protection equipment required by determining potential hazards.

Choose equipment such as spark proof tools if flammable liquids are involved.

Step 9 - Establish decontamination and first aid stations

Establish decontamination procedures in the event that someone is injured. Arrange for medical

assistance and support if necessary. Material Safety Data sheets will provide health and medical

data for the hazardous material.

Step 10 - Contain the spill

The goal is to limit the spread of contaminant and thus maximize safety and minimize liability

costs.

Step 11 - Clean up the spill

The goal here is to limit the spread of contamination, remove contaminant from protective clothing

before removal, and clean equipment. Absorbents used to clean up the spill are often classified as

hazardous waste. Absorbed materials have the same properties as the spill material. Absorbents

must be properly packaged for disposal according to municipal, provincial and federal regulations.

Step 12 - Investigate and evaluate

To remove an ink stain from jeans, you can dab the stain with a cotton ball soaked in rubbing alcohol or use a commercial stain remover specifically designed for ink stains. Gently blot the stain, and then launder the jeans according to the care instructions. Repeat the process if necessary until the stain is no longer visible.