Massey Ferguson

To add hydraulic oil to a Massey Ferguson 399, locate the hydraulic oil reservoir, which is typically found near the rear of the tractor. Remove the filler cap, and use a funnel to pour in the appropriate hydraulic oil, ensuring you check the oil level with the dipstick to avoid overfilling. Always consult the owner's manual for specific oil type and capacity recommendations.

Well, honey, for that Massey Ferguson gc 2400, you're gonna want to use some good ol' diesel engine oil. Make sure it meets the manufacturer's specifications, or you'll be in for a rough ride. And don't forget to change it regularly, unless you want your tractor to kick the bucket sooner than later.

The quickest and best way is to look at the battery. If your positive cable (+) is going to the frame or body, positive ground. If the negative (-) goes to the frame or body, negative ground. I believe that a MF 35 is a neg ground system but use the check from above.

The weight of a Massey Ferguson 285 tractor is approximately 5,500-6,000 pounds.

Massey Harris was a Canadian agricultural machinery manufacturer, founded in 1891. The company was headquartered in Toronto, Ontario, Canada. Today, Massey Harris no longer exists as an independent entity.

Caswell-Massey is a luxury personal care and fragrance company, renowned for its heritage and quality products. Established in 1752, it is one of the oldest continually operating companies in the United States, known for its soaps, perfumes, and grooming products. Today, Caswell-Massey continues to uphold its tradition of providing high-end, classic grooming essentials.

There is a spout on the rear close to under the seat. See picture

5 foot X 6 foot

run the twine through the eyelets and through the needles , which are the large arms that rise up . take that twine and tie to the rear of the baler,both of them and run them where the bale forms. next trip the wheel that ties the bale, and turn the baler by hand for one cycle. the twine will be tied now cut the excess twine that u tied to the rear of the baler from the needles and you are ready to bale .

Drain oil

Remove the right hand side round speed control cover

Remove the small roller that the vertical arm acts on, you just spread the fork it sits in

Remove all bolts around the top cover, not the 4 nuts they hold the levers in place

Use a chain block and a lifting plate, which can bolt onto the seat bolts to lift the top cover directly up

Remove the pin holding the pto spline coupling together

Remove the bolts holding the pto cover and pull the pto shaft outwards

This should allow you to unbolt the pump and remove it

Behind front grill in a canister. Simply unscrew the canister and there is a cartridge filter inside. Car Quest carries the replacement filter for around 40 bucks.

To install the hydraulic pump in a 573 Massey Ferguson 4-wheel drive, first ensure the tractor is securely parked and the hydraulic system is depressurized. Remove any necessary covers to access the pump, disconnect the hydraulic lines and wiring, and unbolt the old pump. Install the new hydraulic pump by reversing the removal process—secure it with bolts, reconnect the hydraulic lines and wiring, and finally, check the fluid levels before testing the system.

AS recommended by the manufacturer for the environment in which the machine works.

Using an educated guess I'd say Massey Ferguson.

The cost of a 1965 Massey Ferguson tractor can vary significantly based on its condition, model, and location, typically ranging from $3,000 to $10,000. Restored or well-maintained models may command higher prices, while those in need of repairs may be less expensive. It's advisable to check local listings or auction sites for the most accurate pricing.

To check the transmission oil on a 1130 Massey Ferguson tractor, first ensure the tractor is on a level surface and the engine is off. Locate the dipstick or fill plug, usually found on the side of the transmission housing, and remove it to clean and then reinsert without screwing it back in to check the oil level. The oil should be within the designated range on the dipstick; if it's low, add the appropriate transmission oil as specified in the operator's manual. Always check for leaks and ensure the oil is in good condition.

To replace the hydraulic filter on a Massey Ferguson 2600, first, ensure the tractor is turned off and parked on a level surface. Locate the hydraulic filter, which is typically near the hydraulic pump or reservoir, and place a drain pan underneath to catch any fluid. Unscrew the old filter using an appropriate tool, apply a thin layer of hydraulic oil to the gasket of the new filter, and install it by hand until snug. Finally, refill the hydraulic system if necessary, and check for leaks before starting the tractor.