Volume

None, since there can be no conversion. A kilogram is a measure of mass. A pint is a measure of volume. The two measure different things and, according to basic principles of dimensional analysis, conversion from one to the other is not valid.
If you are not convinced, consider a pint of air. How many kilograms? Next consider a pint of water. How many kilograms? The masses of equal volumes of the two substances will clearly be very different. So there is no direct conversion between mass and volume: you need to know the density of the substance to enable you to carry out the conversion.

There is no direct conversion between gallons and feet as they are measuring different quantities (volume vs. length). If you specify the shape or container for which you need the conversion (e.g., a rectangular tank), a calculation can be made to determine the height in feet for a volume of 150 gallons.

The density of cooking oil ranges from 910 to 930 kilograms per cubic meter or 0.91 to 0.93 grams per cubic centimeter . So 1 litre of cooking oil weighs 910 to 930 grams or 0.91 to 0.93 kilograms.

According to Wikipedia the density of copper at room temperature is 8.94g/cm3. According to your calculation the density is 8962 kg/m3.

100 centilitres make 1 litre
Considering that the prefix centi- means hundred, then there's probably 100 centiliters in a liter.

Remember K H D | d c m (kilo, hecto, deka, (liter, meter, gram), deci, centi, milli). Kiloliters are three places to the left of liters. So you have to move the decimal place three times to the left. You will get 356 L = .356 kl.

1 dm3 is equal to 1 liter. They are equivalent volumes, with 1 liter being the same as 1 cubic decimeter.

(14 cups) / (2 cups per pint) = 7 pints

the average bath takes 225 litres to fill.

There are approximately 283.9 liters in 75 US gallons.

A 427 engine typically refers to the engine displacement, which is measured in cubic inches in the case of American engines. The equivalent in liters is approximately 7.0 liters.

16 ounces

20 fluid ounces = 1 pint (Imperial)

Depends on the depth. If it is 4 feet deep and it is cicular with a diameter of 24 feet then you have approx. 13,553 gallons of water. If it is 3 feet deep then you have approx. 10,152 gallons of water.

One half a pint.

In US measure, 1 pint = 2 cups And 1 cup = 0.5 pint.

There are 16 US fluid ounces, 2 cups in 1 US pint (473.2 ml).

Although there are 20 Imperial fluid ounces in 1 Imperial pint (568.3 ml), the Imperial system does not have cups, so it is best to use half pints.

In English measurements a pint glass measures to hold 16 ounces. 1 ounce equals 29.5735 milliliters. A total of 473.176 milliliters can be held by 1 pint glass.

To convert 1 liter of xylene to 1 kg, you would need to know the density of xylene. Assuming the density is around 0.87 g/cm^3, 1 liter of xylene would weigh approximately 870 grams (0.87 kg). To reach 1 kg, you would need around 1.15 liters of xylene.

18 pints

1 quart = 2 pints

1 pint = 0.5 quart

10.56 tbsp

1 cup = 16 tablespoons

1 tablespoon = 0.06 cup

10 L is bigger than 1000 mL. 10 L is equal to 10 000 mL.

There are approximately 0.396258 gallons in 1500 milliliters.

The volume doubles

One US cup is 8 oz and right about 237ml or .237 liters.

A liter is 1000ml.

So you would need just about 4.22 cups to equal a liter - or just a bit less than 4 1/4 cups...

All of this assumes "US Customary Cups" typically used in cooking

http://en.wikipedia.org/wiki/Cup_%28volume%29
0.23 liter

There is no sensible answer to this question. A litre is a measure of volume, with dimensions [L3]. A kilogram is a measure of mass, with dimensions [M]. Basic dimensional analysis teaches that you cannot convert between measures with different dimensions without additional information. Even a few seconds of thought will tell you that 40 kg of air will occupy far more volume than 40 kg of lead.