answersLogoWhite

0

What else can I help you with?

Related Questions

You have error 808 for canon ir 2016j?

This message error is due to electric power. i.e the power is not enough to warm up the fuser


How do you resolve E50 error in Canon Printer?

Is your Canon printer showing the e50 error code, and do you want to solve it? Your printer can show this error code when it is facing a failed fuser problem. If your device shows this issue, then you will not be able to print any documents. You can try various steps to fix this issue from your Canon printer. Below are the steps you need to follow to do that. Pressing and holding the STOP/RESET/Resume button for at least 10 seconds. Inspect the LAN connection and internet connection on your device. Make sure that the ink cartridge is installed properly in your device. Restart your Canon printer and computer device. Change the fuser unit from your printer device. Update the printer driver.


What is error message c-fc24 on a konica minolta bizhub c280?

The error message c-fc24 on a Konica Minolta Bizhub C280 indicates a problem with the fuser unit, specifically related to the fuser temperature being outside the expected range. This could be due to a malfunction in the fuser assembly, a faulty thermistor, or issues with the power supply to the fuser. To resolve the issue, it's recommended to check the fuser for any obstructions, ensure proper connections, and consider replacing the fuser unit if necessary. If the problem persists, consulting a technician or the service manual may be required.


How do you fix a 13.20 error on a hp laserjet 9000 printer?

There is a problem with the fuser that has damaged the DC controller. You will need to replace the DC controller and fuser at the same time.


Canon D880 how to remove paper jam in fuser?

To remove a paper jam in the fuser of a Canon D880, first turn off the printer and unplug it for safety. Open the printer’s front cover and carefully remove any visible jammed paper, pulling gently to avoid tearing. If the paper is stuck in the fuser unit, locate the fuser access cover (usually at the back or bottom) and carefully open it to remove the jammed paper. Once cleared, close all covers, plug the printer back in, and turn it on.


What part of HP LaserJet Printer is malfunctioning if you receive 50 service error?

Deffective Fuser.


How do you remove fuser temperature error of sharp am410 fax machine?

There does not appear to be a Sharp AM 410 model, but there is an AM 400 model. There is no specific troubleshooting solution to that error listed in the manual. If you have a system error, the solution is to power the machine off, unplug it, then power it on again. If there is still a system error code, then call for support. Generally, a fuser temperature error that won't go away can mean that either the fuster or the sensor needs to be replaced.


What is fault code F-35-1 on konica 7222?

Fault code F-35-1 on the Konica Minolta 7222 typically indicates a problem related to the fuser unit, specifically an issue with the fuser temperature or a malfunction in the fuser thermistor. This could result from a variety of causes, including a faulty fuser assembly, poor connections, or an issue with the printer's control board. To resolve the error, it's recommended to check the fuser unit for proper installation, inspect wiring, and potentially replace the fuser if necessary. Always refer to the service manual for detailed troubleshooting steps.


What is a hp color laserjet printer 59.30 error?

The error stands for:59.XY PRINTER ERRORX is in your case 3 : FUSER MOTOR STARTUP ERROR.Y is in your case 0 : NO COLORThe service manual says:1. Reconnect the connectors for the fuser motor and on the DC controller PCB. Replace any damged parts.2. Replace the fuser drive assembly.3. Replace the DC controller PCB. Calibrate the Answers.com after replacing the DC controller.


When was Diego Fuser born?

Diego Fuser was born on 1968-11-11.


Do bubble jet printers use a fuser assembly?

no. There is no fuser in a Bubble Jet Printer.


What is fuser oil?

Dimethyoxysiloxane