0
What else can I help you with?
What cables are needed to hook my DTV box to speakers?
The familiar red and white RCA jacks are needed to hook your Direct TV receiver up to an audio source.In general you'll need a stereo receiver to hook it up to speakers.You do get superb audio from DTV so it's worth the trouble.
Is there any way to hook up headphones to cable TV without cutting out the TV sound?
Run the audio through a receiver and speakers. Most receivers will let you hook up headphones and the speakers can either be on or off.
How can I hook up surround sound to my home entertainment system?
To hook up surround sound to your home entertainment system, you will need a receiver that supports surround sound, speakers, and speaker wires. Connect the speakers to the receiver using the appropriate wires, and then connect the receiver to your TV or media player using HDMI or optical cables. Adjust the settings on your receiver to enable surround sound, and enjoy immersive audio experience.
How do I hook up Bose speakers to sharp LC60LE831U?
To connect Bose speakers to a Sharp LC-60LE831U TV, first, check if your Bose speakers are passive or active. For passive speakers, you'll need a compatible AV receiver that connects to the TV via HDMI, optical, or audio cables, and then connect the speakers to the receiver. If the Bose speakers are active, you can connect them directly to the TV using the audio output (either via a 3.5mm headphone jack or optical output) to the speakers. Ensure to configure the audio settings on the TV for the correct output.
What do i need to hook my TV to the home theater?
For most home theater setups, all you really need is an RCA cable to connect your TV to the stereo receiver.
How do you hook up a digital converter to a satellite receiver in order to get local channels you have to pay extra for through direct tv.?
Why would you need to hook up a digital converter to a satellite receiver ? Arn't they already digital ? stevecooper75@comcast.net
Is there a way to connect speakers to a tv that has no audio outputs?
You could use an external cable or satellite receiver and connect speakers to that.
Where do the cables from a Purtone HPD -710 connect to on to a Emerson tv?
The Purtone HPD-710 system consists of passive speakers that need an amplifier to drive them. Unfortunately, even the subwoofer needs an amp. An Emerson TV will not have speaker outputs, it will have RCA line-level outputs. You must plug the TV into a surround-sound receiver to amplify the signal. Then connect speaker cables from the receiver to the Purtone speakers. Since the sub has no amp, you will need a receiver with a subwoofer amp function, which are not common.
Do they make wireless surround sound?
Yes they do make wireless surround sound. If you purchase wireless receiver box you will have speakers that are in the front (which doesn't need to be wireless since it's connected to you TV) and you have the right and left which rest behind you. The wireless receiver box connects to a power outlet and sends the single to the two rear speakers. This setup eliminates running speaker wires from the receiver to your speakers.
How do you hook up a new HD receiver with only one coax input place to an old tv which with old receiver had 2 coaxspots 1 went from tv to incoming dish line then other from tv to back of receiver?
I am assuming you have a new HD duo receiver (222k, 622, 722, 722k) or 612 solo receiver that doesn't have a coax connector for TV 1. You need to do 1 of 2 things to enable you to connect the old TV to your receiver. If your TV has an RCA port (yellow, white, and red cable) on the back, you can use that cable instead of the coax from the TV to the receiver. If your TV doesn't have the RCA ports, you need to get an RF modulator to convert the signal from the receiver from RCA to coax.
How do you set up surround sound on a LG smart TV?
The direct answer to this would be, no. But I think you might be asking the wrong question. To get surround sound to play your television programs you would need to put your cable/satellite box through the receiver. As a side note: There are two ways to do this. 1. If you receiver supports video pass thru (which would mean that there are VIDEO IN jacks and VIDEO OUT jacks) If not then proceed to the next option. You will hook up everything from the cable/satellite box to the receiver and just one cable, which will be the video signal, to the television. 2. You will hook up only the audio cables to the receiver and a single video cable straight to the television.
How do you hook your ps2 to a dishnetwork receiver?
dishnetwork have no inputs only outpus. use a input on the tv
