0
What else can I help you with?
How do you fix water rising in toilet when flushed?
it's called stop holding down the flusher.
How do you remove the rear plunging joint on a polaris 400 ATV?
http://www.motioncycle.com/fiche_section_detail.asp It appears you need special spring ring pliers. The spring ring pliers I have are not long enough. I'm currently dealing with the same problem. From looking at the parts breakdown, it's apparent the spring ring is what's holding the plunging joint on.
Do aircraft toilets discharge their contents in the air?
No, waste flushed down aircraft lavatories are stored in holding tanks in the plane's lower hold. It is then emptied by trucks at the destination.
What is the anatomy of a sink?
The anatomy of a sink includes a basin for holding water, a faucet for controlling water flow, a drain for removing water, and pipes for connecting to the plumbing system.
When in the Navy toilets flushed into the ocean?
Not any more. In the far past, you simply went over the side. Then toilets were put in and they flushed into the sea. Now they flush into holding tanks. Many ships have specialized systems that dry things out and burns the waste. Others have bacteria, like a septic tank, that process the waste. Others pump the tanks in port into the sewage systems.
Can we place septic tank under the building?
In most localities this is not allowed. However, a sealed holding tank, which can be pumped to a septic system might be allowed, check with your plumbing inspector.
What is the holding tank capacity of a 1997 Tioga Montara?
The 1997 Tioga Montara typically features a holding tank capacity of around 30 to 40 gallons, depending on the specific model and configuration. This capacity is designed to accommodate waste and gray water from the RV's plumbing system. For precise specifications, it is advisable to consult the owner's manual or manufacturer documentation.
What is a vacuum breaker?
A vacuum breaker is a mechnical device used to avoid backflow or a negative pressure in a plumbing system. It typically consists of an air valve with a spring holding it closed. When the pressure within the system is positive, the valve remains closed. When the pressure is negative (less than atmospheric), the negative pressure overcomes the force of the spring holding the valve closed and the it opens, typically allowing normal atmospheric air to enter the system, thereby eliminating the negative pressure. Otherwise, the negative pressure might cause backflow of the plumbing system. ...
How do I remove and replace the clean out cap cover on my plumbing system?
To remove and replace the clean out cap cover on your plumbing system, follow these steps: Locate the clean out cap cover on your plumbing system, usually found near the main sewer line. Use a wrench to loosen the screws or bolts holding the cap cover in place. Once the screws are loosened, carefully remove the cap cover and set it aside. Inspect the cap cover for any damage or wear and replace it if necessary. Place the new cap cover over the clean out opening and secure it in place by tightening the screws or bolts. Make sure the cap cover is securely in place to prevent any leaks or debris from entering the plumbing system. Remember to follow any specific instructions provided by your plumbing system manufacturer for proper removal and replacement of the clean out cap cover.
How can I safely remove a plastic snake drain from my plumbing system?
To safely remove a plastic snake drain from your plumbing system, you should first turn off the water supply to the area. Then, carefully unscrew the fittings holding the snake in place and gently pull it out. Be cautious not to damage any surrounding pipes or fixtures during the removal process. If you encounter any resistance, stop and seek professional help to avoid causing further damage.
How can I remove a vanity top?
To remove a vanity top, first turn off the water supply and disconnect the plumbing. Then, use a utility knife to cut through any caulk or adhesive holding the top in place. Finally, carefully lift and remove the vanity top from the cabinet.
How can I effectively connect PVC pipes for my plumbing project?
To effectively connect PVC pipes for your plumbing project, you can use PVC primer and cement. First, clean and dry the pipe ends. Apply primer to both the pipe and fitting, then apply cement to the same areas. Quickly push the pipe and fitting together, holding them in place for a few seconds to allow the bond to set. Make sure the pipes are properly aligned before the cement dries.
