answersLogoWhite

0

to cut 42 " pipe place the pipe on a set of bearingspower driven .place a torch on a stand so it is steady .have the pipe roll about 10 inches per minute.thatis what we do.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How much does a foot of 42 inch pipe weigh?

42 42.000 STD .375 166.7141.250 42 42.000 XHY .500221.61 41.000 Weights are 166.71 per ft. and 221.61.


What is the cut off measurement of a 90 degree pipe fitting?

pipe size(inch)x38.1


How do you cut a carbon steel pipe 4 inch?

A handheld bandsaw or a cutting torch, along a straight line made by a wraparound pipe marker. our company has the steel pipe machine and you can cut it in 4 inch-haihao pipe fitting group sales@haihaogroup.com


Is it possible to cut or clear out tree roots out of a 2 inch drain pipe?

yes


How many pcs of 4 inch pipe can be cut from a 4 foot stock?

12


Can you cut into cast iron soil pipe with plastic soil pipe?

You can put up to a 2 inch pipe into a 4 inch. If you are putting 4 inch to 4 inch, either take out a section of the cast and put the PVC in or cut out a section and connect the PVC to the cast with rubber sleeves meant for this. You can use a saddle clamp for the 2 inch. It is a half round piece of PVC with a 2 inch connection in it. It is held on with two U bolts that go around the cast pipe. Put it where you need it and mark the 2 inch hole on the cast. Drill a series of 1/8 inch holes around this circle. when you get them all drilled, you can break out the plug. Try to keep it from falling into the cast pipe. Put the saddle clamp on and connect the PVC pipe as needed. Seal the saddle clamp to the cast pipe with plumbers putty.


A pipe that is 36 inches long needs to be cut into two and one fourth in long pieces How many pieces would be cut from this length of pipe?

2 1/4 inch is 9/4 inch long pieces, so if pipe is 36 in long then 36/divided by 9/4 is 36 times 4/9 = 16 pieces


What are the steps to thread iron pipe?

You use a Die to cut the threads. A Die is like a nut for a bolt. It is designed to screw onto the end of the pipe and cut the threads. Clamp the pipe so that it cannot turn, start the die on the pipe while putting oil on the pipe. There is special thread cutting oil but any motor oil will work. This make the cutting easier. Cut about 1 inch of threads on the pipe. Make a couple of turn and back the die up a half of a turn. Do this until you have an inch of thread. Backing the die up gets the shavings out of the cutting grooves. The new threads will be very sharp and will cut if you wipe the oil off with your hand, use a rag. The dies are sized for the size of pipe, 1/2, 3/4 and 1 inch are the most common.


How do you replace the drive belt on a 42 inch cut Murray riding lawnmower?

In order to replace the drive belt on a 42 inch cut Murray riding lawn motor, first remove the blade after disconnecting the spark plug. The drive belt is now exposed for easy replacement.


What tool do you need to remove a cemented on cap off of a drain pipe?

Cut the end of the cap off, about 1/2 inch back from the end and then cut the side of the cap. You should be able to peel the cap off of the pipe. If you have enough pipe, just cut the entire cap off and start with a clean section.


How many times bigger is a 10 inch pipe than a 8 inch pipe?

Every time! lol Seriously a 10-inch pipe is 5/4 of an 8-inch pipe


Do you have a belt diagram for mtd yardman riding mower?

how do you rout a belt for 42 inch master cut 13aj7955059