answersLogoWhite

0

What else can I help you with?

Related Questions

What is the take off measurement for a 8 inch victaulic 45 degree fitting?

The take-off measurement for an 8-inch Victaulic 45-degree fitting is typically around 7 inches. This measurement is used to determine the distance from the centerline of the fitting to the point where the pipe will be cut or connected. However, it's essential to consult the manufacturer's specifications or installation guidelines for precise dimensions, as they can vary slightly.


What an 8 inch 90 degree pipe fitting take off when rolled 45 degrees?

Well, honey, when you roll an 8-inch 90-degree pipe fitting 45 degrees, you're looking at a take off of about 8 inches. It's simple geometry, darling. Just remember, always measure twice and cut once - ain't nobody got time for mistakes in the world of piping!


Do you have a formula for pipe cut piece to 90 degree elbow?

Yes, to calculate the length of pipe needed for a 90-degree elbow, you can use the formula: Length = (Distance from the center of the elbow to the center of the next fitting) - (Radius of the elbow). The radius is typically specified by the elbow type (e.g., short or long radius). Additionally, consider any allowances for fitting tolerances when cutting the pipe.


What does it mean to thread a pipe?

Cut pipe threads on the end so that you can screw a fitting on the pipe. Same as the lid on a jar.


What are the steps to properly install a galvanized pipe compression fitting?

To properly install a galvanized pipe compression fitting, follow these steps: Cut the pipe to the desired length using a pipe cutter. Clean the cut end of the pipe and the inside of the fitting with a wire brush. Slide the compression nut and ferrule onto the pipe. Insert the pipe into the fitting until it reaches the bottom. Tighten the compression nut onto the fitting using a wrench until secure. Check for leaks by turning on the water supply. These steps will ensure a proper installation of a galvanized pipe compression fitting.


How do you install a compression fitting?

To install a compression fitting, first cut the pipe cleanly and squarely. Slide the compression nut and ferrule onto the pipe, then insert the pipe into the fitting. Tighten the nut securely to create a watertight seal.


How can I effectively remove a PVC pipe from a fitting?

To effectively remove a PVC pipe from a fitting, you can use a heat gun to soften the PVC material and then twist and pull the pipe out of the fitting. Alternatively, you can use a PVC pipe cutter to cut the pipe close to the fitting and then remove the remaining piece with pliers or a wrench. Be sure to wear protective gear and work carefully to avoid damaging the fitting or the pipe.


How do you remove barb fitting on cooper pipe?

Either cut it out on the pipe with copper cutters or sweat it out with a plumbing torch.


How can I remove a PVC pipe from a fitting?

To remove a PVC pipe from a fitting, you can use a heat gun to soften the PVC material and then twist and pull the pipe out of the fitting. Alternatively, you can use a PVC pipe cutter to cut the pipe close to the fitting and then remove the remaining piece. Be sure to wear protective gear and work in a well-ventilated area when working with PVC and heat tools.


How do you properly use a compression fitting?

To properly use a compression fitting, first ensure the pipe end is cut cleanly and squarely. Slide the compression nut and ferrule onto the pipe, then insert the pipe into the fitting. Tighten the nut onto the fitting by hand, then use a wrench to secure it further. Check for leaks once the fitting is tightened.


What are the steps for properly installing a compression fitting on a copper pipe?

To properly install a compression fitting on a copper pipe, follow these steps: Cut the copper pipe to the desired length using a pipe cutter. Slide the compression nut and compression ring onto the pipe. Insert the pipe into the fitting until it reaches the bottom. Tighten the compression nut onto the fitting with a wrench until it is secure. Check for any leaks by turning on the water supply. Following these steps will ensure a proper installation of a compression fitting on a copper pipe.


How do you properly install a compression fitting?

To properly install a compression fitting, first cut the pipe cleanly and squarely. Slide the compression nut and then the compression ring onto the pipe. Insert the pipe into the fitting and tighten the nut securely with a wrench. Check for leaks and make adjustments if needed.