0
What else can I help you with?
How you can install lock wire on the bolt heads?
To install lock wire on bolt heads, first thread the wire through a hole in one bolt head, then twist the wire around itself to secure it. Next, thread the wire through the hole in the adjacent bolt head and wrap it around that bolt head as well. Finally, twist the ends of the wire together tightly to prevent the bolts from loosening.
What can unlock most locks?
A lock-picker's tools, which includes a piece of wire.
How do you open a lock with out the key?
Some locks can be picked open when you don't have the key. You can use a wire hanger or a hair pin to pick a lock. If you cannot get the lock open, contact a locksmith for help.
How do you remove a broken key from an ignition?
Locksmiths have a tool that is basically a hooked piece of thin wire. I had a broken key in the lock that i had to remove so i used a very thin piece of wire and made a small 90 degree bend in it. The idea is to slide the wire (hooked end) along the key and get to the end of the key and get the bent end of the wire hooking the tip of the key. Then simply pull the broken end of the key out. In effect you are using a small,long fishhook to get the key out. Use a pair of pliars to bend the wire. Remember that the wire has to be thin and fairly strong. Coat hanger and bailing wire is much too thick. While breaking the lock, if the lock was damaged then you may have to replace the lock. The key may be jammed in too tightly.
Can you Disable the auto door lock on 2008 Yukon the owners manual only allows to change from lock at transmission in gear or at speed I do not want it to lock unless I push the lock switch?
I wanted to do the same with my 2005 f-150, but couldn't find any real answers from anybody at a garage or dealership. I got lucky with my f-150, only because the signal wire from the ECM to the driver's door lock was a separate wire from the rest of the bunch. So I took apart my drivers door, jammed a test light in each and every wire terminal on the harness at the window controls, and drove around. Unlock the doors at a stop, then put the trans in gear and start rolling. They should lock around 5 or 10 mph. When they lock, your test light will light up when you are on the right terminal, showing you the signal wire. When I did that, I just cut the wire. Problem solved. But your vehicle might be different. Try it out and see. Your signal wire might be the same as another wire, so cutting it might effect some other window function all together. GOOD LUCK.
Why apple use fire wire not parallel ports?
To lock their customers into Apple's proprietary products.
What to do when your car jerking?
Pop the lock and hot wire the car so alarm dont go off
How do you get plug out of blower on jeep green wire?
Release the lock tab and pull it out. It may be melted and stuck in there.
How do you install an ignition switch on a 1966 Mustang?
disconnect the battery.put the key in the switch,and turn to the acc position.(on) insert a piece of wire into the hole of the lock cyclinder.push the wire inward to depress the the lock pin,then turn the key counter clock wise and with draw the lock cyclinder.press the rear of the switch and rotate it counter clockwise. remove the bezel,switch and spacer.hope this helps.
How to test door lock?
The best way to test a door lock is to locate the wiring for the door lock usually in door boot or kick panel. Use a test light with a probe and poke each wire until the door lock is activated. How ever be sure to they are not vacumm locks
If i have 1999 Jeep Grand Cherokee and the power locks lock but don't lock the other 3 doors what needs to be replaced?
Check for a broken wire in the harness going to the drivers door.
What is the wiring diagram for a 30 amp 4-prong twist-lock plug?
The wiring diagram for a 30 amp 4-prong twist-lock plug typically includes connecting the green wire to the ground terminal, the white wire to the neutral terminal, the black wire to one of the hot terminals, and the red wire to the other hot terminal. Make sure to follow the specific instructions provided with the plug to ensure proper installation.
