0
What else can I help you with?
How do you get pressure of 100 millibar from propane gas bottle?
To achieve a pressure of 100 millibar from a propane gas bottle, you would regulate the flow using a pressure regulator. Make sure the regulator is compatible with propane gas and set it to the desired pressure. Attach the regulator to the propane gas bottle, open the valve slowly, and adjust the regulator until the pressure gauge reads 100 millibar.
What should I do if the water pressure is too high in my home?
If the water pressure is too high in your home, you should first check if the pressure regulator is set correctly. If it is not, adjust it to lower the pressure. If that doesn't work, you may need to install a pressure reducing valve to regulate the water pressure. High water pressure can damage pipes and appliances, so it's important to address this issue promptly.
What does a furnace regulator do?
A furnace regulator helps to deliver a set pressure and flow rate of gas to the furnace so it burns in a stable condition.
How can I set up a drip irrigation system using a hose bib?
To set up a drip irrigation system using a hose bib, you will need a pressure regulator, a filter, tubing, and drip emitters. Connect the pressure regulator and filter to the hose bib, then attach the tubing to the regulator. Place the drip emitters along the tubing to deliver water directly to the plants. Adjust the flow rate as needed for each plant.
Is the water pressure regulator valve bad if there is no pressure change when you turn the bolt counter clockwise?
I'm assuming you are talking about a pressure regulator on a boiler, the bolt on top is just a locking/ jam nut. The regulator comes set at the factory for 12psi. The shaft threw the center has two notches and can be turned with a large flat screw driver, however useually if they are not bran new they wont turn and tere is rarely a need to.
How do you balance the pressure of your geyser?
To balance the pressure of your geyser, you can adjust the temperature setting on the thermostat to regulate the flow of hot water. You can also check the water pressure regulator on the main water supply line to ensure it is set to the appropriate pressure. Regular maintenance, such as descaling the geyser, can also help maintain proper pressure.
What shoud the fuel pressure regulator be set at on a 1991 Chevy 4x4and im still using the fuel pump in the tank?
You need to hook a fuel pressure gauge to it and adjust the regulator so that you have 9 to 13 LBS, of fuel pressure. No lower are higher.
How do I correct fuel pressure too lean on Honda CRX?
install a fuel pressure regulator and set it to 36 psi idle in a stock motor
Does a gas pizza oven require a gas regulator?
No, you do not "need" a regulator. The oven will work without it. However, the regulator controls the gas pressure. I bought two pizza ovens recently. One had a regulator and got up to the 650 degrees I set it to. The other did not have a regulator and would not rise above 500 degrees.
Why won't an electric fuel pump work on an 1982 Camaro?
it will work but you have to use a pressure regulator in line so you can set the fuel pressure down to 6 psi. for the carburetor
What is a Pressure regulator valve?
A regulator is simply a valve with a preset pressure point that causes the valve to open and close. A pressure sensor (a diaphragm with an adjustable spring) is on the side of the valve that the pressure you want is on. When the desired pressure (we will use 50psi) is reached, it causes the diaphragm to expand against the spring.The diaphran is connected to the valve and when it expands, it closes the valve, letting no more pressure to build. when you flush a toilet or turn on the sink, the diaphragm contracts opening the valve wider and wider until enough water is flowing in to raise the pressure expanding the diaphragm to close the valve. the diaphragm is just like a ballon, the more pressure, the more it expands. the set screw on most regulators puts more or less pressure on the diaprham raising or lowering the amount of pressure needed to move the diaphragm enough to close the valve. do not confuse the regulator with the pressure switch on a pump system. they are not the same. the job of the regulator is to keep constant pressure in your system. the pressure switch on pumps works about the same but has two preset pressures. the first to turn a pump off when the desired pressure is reached and the second to turn it back on. the off pressure is always higher then the on pressure by about 10psi or your pump would be constantly turning on and off.
What is the purpose of having a back pressure valve in marine refrigeration system?
when two refrigerated spaces are severed by only one compresser & condenser but need to be maintained at different temps. a back pressure regulator comes into play. The back pressure regulator will be installed on the outlet of the refrigeration system to maintain a minimum back pressure in the evap coils. Since pressure is directly related to temp. then the temp. desired can be maintained by the pressure you set.
