0
What else can I help you with?
Why is your oil burner off but you still have heat coming from the baseboard?
A baseboard heater runs through a process of induction and release, in a manner of speaking. That is, the burner will heat the water; the water will pump through the system; and once all is up to temperature, the burner will shut down. However, the metal of the pipes and the water itself will not cool right away; it will remain hot for a time and cool slowly. The closer the baseboard is to the furnace itself, the longer it will remain hot.
Our baseboard heater cover is to long after a tile installationhow do we fix it?
The heater can most likely not be shortened. If ceramic tiles were installed then they will have to be cut to expand the opening with great care. The tiles will have to be wet, and the right blade used to prevent shattering. This is cutting wet tile with an electrical tool so electrical shock must be considered.
Where is the heater valve located on a 1994 Mitsubishi Mighty Max truck?
The heater valve is located behind the dash above and to the right of the accelerator pedal. The heater core is right beside it. It is operated by a linkage to the slider on the heater control panel.
How much electric baseboard heat is needed for a house?
The amount of electric baseboard heat needed for a house depends on factors like the size of the house, insulation, climate, and personal preferences for room temperatures. A general estimate is that you need 10 watts per square foot, but it's best to consult with an HVAC professional to determine the right amount for your specific needs.
What does the error code p0155 mean on a dodge ram?
Right upstream oxygen sensor heater failure.Right upstream oxygen sensor heater failure.
Where is the heater control valve on a mustang?
The heater control valve in a Mustang is located within the engine. It is right in the heater's core and where the coolant is located.
How can I properly install electric baseboard heaters in my home?
To properly install electric baseboard heaters in your home, follow these steps: Choose the right size heater for the room. Turn off the power to the area where you will be installing the heaters. Mount the heaters on the wall, making sure they are level. Connect the wiring according to the manufacturer's instructions. Turn the power back on and test the heaters to ensure they are working properly. It is recommended to consult a professional electrician for assistance with the installation to ensure safety and compliance with local building codes.
Block heater on pontiac g6?
The Pontiac G6 block heater is located on the right hand side of the engine. The block heater can be located by following the block heater cord.
How do you get on the bed when the heater is all the way down in shrink ray island?
You have to turn the heater on, by running to the right on it.
What are the best installation techniques for baseboard tile in a bathroom renovation project?
The best installation techniques for baseboard tile in a bathroom renovation project involve proper preparation of the surface, using the right adhesive, ensuring precise measurements and cuts, and finishing with grout for a clean and polished look.
How do you wire a double pole thermostat to two baseboard heaters?
This is wiring 2 baseboard heaters with a double pole wall thermostat you run the power wire to the thermostat on the wall then you run a wire to the 1st heater and then you run another wire from the 1st heater to the 2nd heater and hook red on red and black on black with wiring mariette's in the heaters junction box on left or right side which ever is more suitable for you and then you go to the wall thermostat and hook red on red and black on black with the wiring mariette's and then you hook your power wire to the power supply which is 100 or 200 amp service and on a double 20 breaker and the wire has to be no smaller than 12/2 wire. also do not forget to hook the ground wire (bare copper) on the green screw on your heater and in the thermostat box and then on the power supply box..... now you can turn up your thermostat and enjoy the heat ...........LEE48
Which of the primary bronchi traps foreign object that entered the respiratory passageways?
Foreign objects that enter the respiratory passageways are more likely to become lodged in the right primary (main) bronchus.
