answersLogoWhite

0

Urine, feces, keratinizing fungi, etc. It could also turn orange after hurling beer and Cheetos, with subsequent use.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

How do you install a toilet bowl?

To install a toilet bowl, first, turn off the water supply and drain the existing toilet. Remove the old toilet by unscrewing the bolts and lifting it off the flange. Place a new wax seal on the flange, set the toilet bowl onto the flange, and secure it with bolts. Finally, reconnect the water supply, check for leaks, and ensure the toilet is level.


What should you do when the tip of the toilet auger break off in the toilet?

Remove the bowl turn it up side down and remove theauger head


How can I remove a toilet tank?

To remove a toilet tank, first turn off the water supply to the toilet. Flush the toilet to empty the tank. Disconnect the water supply line and unscrew the bolts connecting the tank to the bowl. Lift the tank off the bowl and set it aside.


Why is there already water in toilet bowls?

Under what circumstance? New toilet, when you turn the water on, water goes down the overflow tube to fill the bowl. You don't have to flush it the first time to fill the bowl.


How can I replace toilet bowl bolts?

To replace toilet bowl bolts, first turn off the water supply and flush the toilet to empty the tank. Remove the nuts securing the bolts at the base of the toilet. Lift the toilet off the bolts and replace them with new ones. Place the toilet back in position and tighten the nuts. Reconnect the water supply and test for leaks.


What causes water to turn gray in a toilet bowl?

I have lived in many places around the world, and have never seen water turn grey is a toilet bowl. I suspect this is a bogus question. Avraham HanadariANS 2 -this MAY happen if the toilet is on a well system and there's lots of fine sediment in the water. - Otherwise, yes, a bogus question.


How do you get the ring out of a toilet bowl?

To remove a ring from a toilet bowl, first, turn off the water supply and flush to empty the bowl. Then, apply a toilet bowl cleaner or a mixture of baking soda and vinegar to the stain, allowing it to sit for about 10-15 minutes. Use a toilet brush to scrub the area, focusing on the ring, and flush again to rinse. For stubborn stains, you may need to repeat the process or use a pumice stone gently.


What is the purpose of the toilet handle arm and how does it function within the toilet system?

The purpose of the toilet handle arm is to lift the flapper or flush valve inside the toilet tank, allowing water to flow from the tank into the toilet bowl to flush waste down the drain. When the toilet handle is pressed, it pulls on the handle arm, which in turn lifts the flapper or flush valve, releasing water into the bowl for flushing.


How can I install a bidet toilet seat?

To install a bidet toilet seat, first turn off the water supply to the toilet. Remove the existing toilet seat and clean the area. Follow the manufacturer's instructions to attach the bidet seat to the toilet bowl. Connect the water supply hose to the bidet seat and the toilet tank. Turn the water supply back on and test the bidet seat.


How can I fully drain a toilet?

To fully drain a toilet, turn off the water supply valve located behind or near the toilet. Then, flush the toilet to remove as much water as possible. Use a plunger to push any remaining water out of the bowl and into the drain. Finally, use a wet/dry vacuum to suction out any remaining water in the bowl and tank.


How do I install a bidet attachment?

To install a bidet attachment, first turn off the water supply to the toilet. Remove the toilet seat and place the bidet attachment on the toilet bowl. Connect the bidet to the water supply and secure it in place. Reattach the toilet seat and turn the water supply back on. Test the bidet to ensure it is working properly.


How do I install a bidet toilet seat?

To install a bidet toilet seat, first turn off the water supply to the toilet. Remove the existing toilet seat and clean the area. Follow the manufacturer's instructions to attach the bidet seat to the toilet bowl. Connect the water supply hose to the bidet seat and turn the water supply back on. Test the bidet seat to ensure it is working properly.