answersLogoWhite

0

It is most likely the thermocouple that is bad. That is what keeps the pilot light on. The thermocouple is the small tube that sits in the flame of the pilot and runs to the control valve.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

How do I turn on the water heater pilot?

To turn on the water heater pilot, locate the pilot light button or knob on the water heater. Turn the knob to the "pilot" setting and hold it down. While holding the knob down, use a long lighter to ignite the pilot light. Once the pilot light is lit, continue holding the knob down for about a minute before releasing it. This should successfully turn on the water heater pilot.


How do I turn on a hot water heater?

To turn on a hot water heater, locate the pilot light or ignition switch on the unit. Follow the manufacturer's instructions to safely ignite the pilot light or turn on the heater using the ignition switch. Allow the water heater to heat up before using hot water.


How do I turn on the pilot light for my water heater?

To turn on the pilot light for your water heater, locate the pilot light assembly near the bottom of the water heater. Turn the gas control knob to the "pilot" setting and hold it down. While holding the knob down, use a long lighter to ignite the pilot light. Once the pilot light is lit, continue holding the knob down for about 30 seconds before releasing it. If the pilot light stays lit, turn the gas control knob to the "on" position to start the water heater.


How do you turn off a heater pilot light?

Same as any hot water heater. Turn the gas valve to off.


How do I turn on a gas water heater?

To turn on a gas water heater, locate the pilot light and turn the knob to the "pilot" setting. Press and hold the knob down while using a long lighter to ignite the pilot light. Once lit, continue holding the knob down for about 30 seconds before releasing it. Then, turn the knob to the "on" position to start the water heater.


How do I turn on the water heater pilot light?

To turn on the water heater pilot light, locate the pilot light assembly near the bottom of the water heater. Turn the gas control knob to the "pilot" setting and press it down. While holding the knob down, use a long lighter to ignite the pilot light. Keep holding the knob down for about 30 seconds, then release it. If the pilot light stays lit, turn the gas control knob to the "on" position. If it doesn't stay lit, repeat the process.


How do I turn on the pilot light on my water heater?

To turn on the pilot light on your water heater, locate the pilot light assembly near the bottom of the water heater. Turn the gas control knob to the "pilot" setting and hold it down. While holding the knob down, use a long lighter to ignite the pilot light. Keep holding the knob down for about 30 seconds, then release it. If the pilot light stays lit, turn the gas control knob to the "on" position. If it doesn't stay lit, repeat the process.


How to light a water heater with an electronic pilot by Honeywell?

To light a water heater with an electronic pilot by Honeywell, follow these steps: Locate the control panel on the water heater. Turn the control knob to the "Pilot" position. Press and hold the pilot button while pressing the ignition button. Continue holding the pilot button for about 30 seconds to allow the pilot flame to ignite. Release the pilot button and turn the control knob to the desired temperature setting. Always refer to the manufacturer's instructions for specific details on lighting your water heater.


What are the steps to relight the pilot on a hot water heater?

To relight the pilot on a hot water heater, follow these steps: Locate the pilot light assembly on the water heater. Turn the gas control knob to the "off" position and wait for at least 5 minutes. Turn the gas control knob to the "pilot" position. Press and hold down the pilot button while using a long lighter to ignite the pilot light. Continue holding down the pilot button for about 30 seconds after the pilot light is lit. Release the pilot button and turn the gas control knob to the desired temperature setting. Remember to refer to the manufacturer's instructions for specific guidance on relighting the pilot on your particular water heater.


How do I change the gas valve on a water heater?

To change the gas valve on a water heater, first turn off the gas supply and water heater. Disconnect the gas line and pilot tube from the old valve. Remove the old valve and install the new one in its place. Reconnect the gas line and pilot tube, then turn the gas supply and water heater back on.


How can I relight the water heater pilot?

To relight the water heater pilot, locate the pilot light button or knob on the water heater. Turn it to the "pilot" setting and hold it down. While holding the button down, use a long lighter to ignite the pilot light. Keep holding the button for about a minute after the pilot light is lit to ensure it stays on. If the pilot light continues to go out, there may be an issue with the thermocouple that needs to be addressed by a professional.


How do I properly light the pilot on my water heater?

To properly light the pilot on your water heater, follow these steps: Locate the pilot light button or knob on the water heater. Turn the knob to the "pilot" setting and hold it down. While holding the knob down, use a long lighter to ignite the pilot light. Keep holding the knob down for about 30 seconds after the pilot light is lit. Release the knob and turn it to the "on" position. If the pilot light goes out, repeat the process. If it continues to go out, there may be an issue that requires professional assistance.