From what I have researched and discovered your normal antenna that you have should suffice in picking up the digital signal. Mine at home is working fine with it. Just be careful because the stores are going to try and say you need to get a new antenna when in reality there is not a single difference in design or material or calibration of any sort. That person has not had trouble so far because it has not switched to strictly digital yet.
A Hertz antenna refers to a type of dipole antenna that was invented by the German physicist Heinrich Hertz. It is a simple antenna design with two conductive elements used for transmitting or receiving electromagnetic waves at radio frequencies.
The radiation resistance of a folded dipole antenna is typically higher than that of a simple dipole antenna, approximately 300 ohms compared to 73 ohms. This increase in radiation resistance helps improve the efficiency and performance of the antenna. The folded design allows for a more compact structure while maintaining good radiation characteristics.
The Yagi array allows a significant increase in antenna gain (expressed in dBi or Db over isotropic) by the simple addition of parasitic elements to a dipole or folded dipole.
I don't think it has. Bandwidth depends on the diameter to length ratio of the antenna. The greater the diameter of the elements the wider the bandwidth. The inductance goes down and the capacitance goes up, giving the antenna a lower Q. the folded dipole has a greater effective diameter (at least double for the same materials). You can increase a normal dipole's bandwidth by increasing the diameter, hence the old time birdcage aerials.
A dipole antenna, is a radio antenna that can be made of a simple wire, with a center-fed driven element. It consists of two metal conductors of rod or wire, oriented parallel and collinear with each other (in line with each other), with a small space between them. The radio frequency voltage is applied to the antenna at the center, between the two conductors. These antennas are the simplest practical antennas from a theoretical point of view. They are used alone as antennas, notably in traditional "rabbit ears" television antennas, and as the driven element in many other types of antennas, such as the Yagi. Dipole antennas were invented by German physicist Heinrich Hertz around 1886 in his pioneering experiments with radio waves.
I have not seen any digital TVs with a built in antenna. Depending on where you live you could use a simple "rabbit ears" setup or even one with a built in amplifier if you're a bit far from the stations.
All types... depending on frequency and application. Lower frequency RFID's are typically near field and use inductive antenna designs, higher frequency ones use far-field designs. Low frequency RFID's like the TIRIS pet ID's use coils of wound wire. HF type RFID's like MiFARE use simple planar loop antenna designs. Most VHF RFID's use dipole and modified dipole designs with reflector elements. UHF and microwave RFID's frequently use patch and slot antenna designs.
A thin wire antenna, such as a dipole or monopole, is a simple and efficient antenna design that is often used for receiving or transmitting radio signals. The current distribution on a thin wire antenna is non-uniform and varies along the length of the wire. At the center (feedpoint) of the antenna, the current is typically at its maximum, decreasing towards the ends. This current distribution creates a radiation pattern that determines the directionality and gain of the antenna.
Its simple, The antenna of the T.V was broken and could not be fixed so a new antenna had to be bought
== == For digital TV, you can build a DB4 antenna out of wire coat hangers and a piece of wood. Very simple to make. There are step by step instructions here - www.TheTutorGenie.com/DigitalAntenna.html - It works great. It depends on what you want to do with it. A receiving antenna for 40 m shortwave could be just a long piece of wire tacked to the walls. An antenna to transmit and receive at 440 MHz is a completely different animal. Here's a fun web site: http://www.ac6v.com/antprojects.htm
The cost of repairing drywall damage would depend on how much damage is done. If you were to buy the drywall it ranges from $10 to $30 a sheet. Plus if you hired someone then it would cost more for labor then it would if you did it yourself.
A better simple approximation would be two antennas separated by twice the distance of the single antenna to the ground.