0
What else can I help you with?
Where can I get a rebuild kit for a FordOMatic 2 speed Transmission?
online eBay or Craig's list come on dude!
How do you change the clutch in a 1994 Camaro 3.4L five speed?
raise the car, drain the transmission fluid, remove any exhaust components that will get in the way of the transmission, remove the starter, remove the drive shaft, remove transmission crossmember, use an engine hoist or a jack to support the engine, remove slave cylinder from bellhousing, remove transmission and bellhousing, unbolt pressure plate, inspect all components replace bad parts, reassemble. DON'T FORGET TO REFILL TRANSMISSION
Where is the slave cylinder on a 1987 Ford Tempo with a 2.3 5-speed?
It's attached to the front of the bellhousing on the transmission.
Can a T5 transmission be put into a 200 ci V6 3-speed 67 Mustang?
It is doubtful as the bolt pattern on the bellhousing is most likely different.
How do you troubleshoot and or fix the speedometer on a 98 Dodge Ram 1500 4x4 when it starts bouncing?
Replace the speed sensor, usually mounted on the transmission bellhousing.
What kind of 4 speed manual transmission is in an 86 dodge D100 with a slant 6 and will it bolt up to a 318?
a-833 overdrive four speed. dodge started making them in 1975. it will bolt up to a 318 provided you have the correct bellhousing for the 318 as the ;leaning tower of power' bellhousing wont fit.
What 6 speed trannys will fit a 1973 Chevrolet Nova with a 350?
Or what 4 speed manual transmissions will fit.Will a M22 bolt to the 350 and fit the car?TransmissionsYou can use the Muncie, Saginaw, or Borg Warner four speed transmission on the 350 engine also it may be possible to mate up the Borg Warner T56 6 speed manual. It was available in the 04-07 corvette, the 04-06 GTO, and the 04-06 Cadillac CTS. It has a hydraulic clutch and an 11 inch clutch disk.D&D Performance makes a kit for $3.5k that lets you bolt a viper six speed to a 350 engine's bellhousing using an adapter plate (you need an engine, flywheel, clutch, and bellhousing).McLeod makes a $500 bellhousing that adapts a viper transmission to a t56 transmission (you need an engine, flywheel, clutch, and a viper transmission).McLeod also makes an adapter plate that lets you bolt a GM's t56 to a standard Chevy bellhousing for $250 (you need an engine, flywheel, clutch, bellhousing, and transmission.ddperformance.com for the Viper six speed.summitracing.com for the McLeod stuff.
Where is the output speed sensor located on a 2000 Nissan Maxima?
it is located in the left wheel well...Remove the left whell and you should see it on top of the bellhousing(transmission)..this link shows pictures and OEM part number you will need to order the part: http://picasaweb.google.com/cefiro.calsonic/P0720VSS# otput speed sensor
Where is the speed sensor for a 2001 Nissan Maxima?
The speed sensor (transmission revolution sensor) is located on the left side of the bellhousing near the top. Access is through the driver's side wheel well. I'm at the wheel well and i cant see the speed sensor
How do you change the clutch in an erf 16 speed?
To change the clutch in an ERF 16-speed truck, first ensure the vehicle is safely parked and secured. Begin by removing the transmission and associated components, including the driveshaft and bellhousing. Once the transmission is out, you can access the clutch assembly; remove the old clutch and replace it with a new one, ensuring proper alignment. Finally, reassemble the transmission and components, and check the clutch operation before driving.
Will the 5 speed manual transmission from a 92 3.1 work with a Chevy v8?
Yes, but you will need a v8 bellhousing. And depending on how much power that v8 is putting out, will depend on how long the transmission last. they are rated for about 300 HP
How do you remove a stick shift for a f150 4 speed transmission?
what are you wanting to take the transmission out completely or what?
