0
What else can I help you with?
What is the proper overhang for a stair tread over the riser?
No more than 1-1/4 inch.
How many inches does the Stair tread depth typically stick out more than the run?
there are no set inches .... stairs are cut to a RATIO of the amount of space you need to climb [ say to the second floor of a house or to the top of a deck ] the steeper you make the stairs the higher this ratio will be. 10 inches of tread - and 8 inches of rise - is a common ballpark figure ... you cannot just decide i want my steps to be ______ height. you much use math and figure out how many steps can be divided equally into the total height. local building codes sometimes set a minimum and maximum height to the individual risers. making steps with one odd sized riser [ say shorter or higher than all the rest of the stairs so that it comes out correctly- and usually on the bottom step ] is a HUGE no-no as well. things too look up on the web are "framing square" and "stair stringer"
If stair tread is 7 inches and run is 11 inches will there be a 1 inch overhang?
A "tread" and a "run" are the same thing. Your question negates itself. However, if what you meant was an 11" riser and a 7" tread, then what you are describing is a ladder, as it would have an angle greater than 50 degrees. Ideally, you should reverse the dimensions, in which case then, yes, a 1" overhang is appropriate.
If you are measuring a rise for a 10ft stair what would it be?
The current standard for stairs in the US is a maximum of 7" per riser.10' is 120", divided by 7" is just over 17,but since the maximum allowable is 7" you're going to have to have 18 risers at 6 2/3"Don't panic, your framing square has one leg divided into 12ths,8/12 = 2/3
In nabooti island after you pass the scorpian how do you get on the top stair?
you cant pass the scorpian but you have to press the thing right befor you drop on the floor by the scorpian you have to make them all horizontal
How do you layout a stair?
Minimum tread is 10" and maximum riser is 7.75".
What is the maximum stair rise and minimum tread for industrial stairs?
Normally 7" rise and 11" run.
The stair tread depth is typically- more than the run so that it sticks out nose?
Nosing is not taken into account when calculating initial stair set-out, but added later. The rise of a residential stair in the US is 8" and the run is 10" with a nose of 1". This means that the tread depth is 10", the height from stair to stair is 8" and the tread sticks out 1" over the the tread below. It is still 10" from front to back. A commercial stair is 7" rise, 11" run, 1" nose.
What are the standard stair dimensions for residential buildings?
The standard stair dimensions for residential buildings typically include a riser height of 7 inches and a tread depth of 11 inches.
Where can one purchase stair tread?
You can purchase stair tread from interior and you can purchase online or in the store this is perfect for carpeted stairways can be painted or covered
What is the difference between stair tread and stair riser?
The tread is what you step on, the riser is the part going up. Rise=riserThe tread is what you step on. The riser is the upright piece your toe hits.
How can I remove a stair tread?
To remove a stair tread, first, use a pry bar to carefully lift the tread from the stairs. Then, remove any nails or screws holding the tread in place. Finally, gently pull the tread away from the stairs to fully remove it.
How wide should stair treads be in new construction?
The standard length of a stair tread is 13' with a height of 1'. To learn more got to "www.stair-treads.com". This website will answer any other questions you may have.
What is the definition for tread?
As a verb, tread means the way someone is walking. As a noun, tread can mean the top of a stair (where you step on), or the tread of a tire.
What part of your body is part of a stair tread?
that one there
What is the average stair tread depth typically recommended for residential buildings?
The average stair tread depth recommended for residential buildings is around 10 to 11 inches.
What are some of the most popular manufacturers of stair tread rugs?
Some of the most popular makers of stair tread rugs are, Dean, Jefferson and Smithfield. You can buy these stair rugs at Home Depot, Macy's and JC Penney's.
