answersLogoWhite

0

No more than 1-1/4 inch.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Trigonometry

If stair tread is 7 inches and run is 11 inches will there be a 1 inch overhang?

A "tread" and a "run" are the same thing. Your question negates itself. However, if what you meant was an 11" riser and a 7" tread, then what you are describing is a ladder, as it would have an angle greater than 50 degrees. Ideally, you should reverse the dimensions, in which case then, yes, a 1" overhang is appropriate.


What is the maximum height on a stair tread?

The correct response varies per building codes. However, the most common is 7 3/8".


How many inches does the Stair tread depth typically stick out more than the run?

there are no set inches .... stairs are cut to a RATIO of the amount of space you need to climb [ say to the second floor of a house or to the top of a deck ] the steeper you make the stairs the higher this ratio will be. 10 inches of tread - and 8 inches of rise - is a common ballpark figure ... you cannot just decide i want my steps to be ______ height. you much use math and figure out how many steps can be divided equally into the total height. local building codes sometimes set a minimum and maximum height to the individual risers. making steps with one odd sized riser [ say shorter or higher than all the rest of the stairs so that it comes out correctly- and usually on the bottom step ] is a HUGE no-no as well. things too look up on the web are "framing square" and "stair stringer"


What angle should the stair railings be?

Stair railings should typically be installed at an angle of about 30 to 40 degrees relative to the horizontal plane. This angle provides effective support and comfort for users as they ascend or descend the stairs. It's important to ensure that the railing height is also within the building codes, usually around 34 to 38 inches above the stair tread. Always consult local building regulations for specific requirements.


Related Questions

What is the difference between stair tread and stair riser?

The tread is what you step on, the riser is the part going up. Rise=riserThe tread is what you step on. The riser is the upright piece your toe hits.


How do you layout a stair?

Minimum tread is 10" and maximum riser is 7.75".


If stair tread is 7 inches and run is 11 inches will there be a 1 inch overhang?

A "tread" and a "run" are the same thing. Your question negates itself. However, if what you meant was an 11" riser and a 7" tread, then what you are describing is a ladder, as it would have an angle greater than 50 degrees. Ideally, you should reverse the dimensions, in which case then, yes, a 1" overhang is appropriate.


What is the recommended measurement for stair tread overhang to ensure safety and aesthetics in a staircase design?

The recommended measurement for stair tread overhang is typically around 1 to 1.5 inches. This overhang helps provide stability and safety while also enhancing the overall look of the staircase.


How to install stair risers effectively and securely?

To install stair risers effectively and securely, follow these steps: Measure and cut the riser to fit the height of the stair. Apply construction adhesive to the back of the riser. Place the riser against the stair tread and secure it with finishing nails or screws. Repeat for each stair riser, ensuring they are all level and securely attached. Finish by caulking any gaps and painting or staining the risers for a polished look.


How to install risers on stairs effectively?

To install risers on stairs effectively, follow these steps: Measure the height and width of each stair riser. Cut the riser material to the appropriate size. Apply construction adhesive to the back of the riser. Press the riser firmly against the stair tread. Secure the riser in place with finishing nails or screws. Repeat the process for each stair riser. Allow the adhesive to dry completely before using the stairs.


What are the standard stair dimensions for residential buildings?

The standard stair dimensions for residential buildings typically include a riser height of 7 inches and a tread depth of 11 inches.


What are all the Stair parts?

Tread, riser, stringer, spindle, newel post, hand rail. fillet, shoe moulding, dowelling, screws, glue.


Standard dimenions of a stair unit?

The current standard for a stairway in a public building is a tread that is no less then 12" deep (this can include a rounded nosing) with a rise of no more the 7". The tread should overhang the place where the previous step joins the riser by 1".This is for new work. If you're making a repair or renovating a residential structure, there may be allowances. Check with the local building inspector.


What is a stair piece?

stringer is the support piece, usually under both sides and one in the middle riser is the front piece tread is the flat piece you walk on


Where do you measure from to determine the height of a stair hand rail?

Measure from the nose and the top of the tread of the plumb up the wall 34' to 36'


What is the purpose of stair tread nosing and how does it enhance the safety and durability of staircases?

Stair tread nosing is the rounded edge of a stair step that extends slightly over the riser below. It helps improve safety by providing better visibility of the edge of the step, reducing the risk of tripping. Additionally, the nosing protects the edge of the step from wear and tear, increasing the durability of the staircase.