you connect everything to the <3 dude
you connect everything to the <3 dude
* Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.) * Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.) * Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.) * Step 4: Bolts 1 - 8 turn an additional 1/4 Turn. (Do not use a torque wrench for this step.)
highly unlikely.
{| |- | NOTE Step 1: Tighten all bolts to 22 ft. lbs. Step 2: Tighten all bolts to 51 ft. lbs. Step 3: Loosen all bolts, in reverse torque sequence, by 180° Step 4: Loosen all bolts, in reverse torque sequence again by 180° Step 5: Tighten bolts #1 and #2, in the torque sequence, to25 ft. lbs. Step 6: Tighten bolts #3,4,5 and #6, in the torque sequence, 11 ft. lbs. Step 7: Tighten all bolts, in torque sequence, by 80-90° Step 8: Tighten all bolts, in torque sequence, again by 80-90° |}
STRAIGHT FROM THE 1998 HONDA CIVIC MANUAL 1ST STEP 14 FT LB BOLTS 1-10 2ND STEP 36 FT LB BOLTS 1-10 3RD STEP 49 FT LB BOLTS 1-10 4TH STEP 49 FT LB BOLTS 1-10 9 3 1 5 7 8 6 2 4 10
Tighten the cylinder head bolts 1-8 in the sequence shown. Using the 4 step torque turn method, tighten according to the following values:Step 1: Bolts 1 - 8 to 61 Nm (45 ft. lbs.)Step 2: Bolts 1 - 8 to 88 Nm (65 ft. lbs.)Step 3: Bolts 1 - 8 (again) to 88 Nm (65 ft. lbs.)Step 4: Bolts 1 - 8 turn an additional 1/4 turn. Do not use a torque wrench for this step.NOTE: Bolt torque after 1/4 turn should be over 122 Nm (90 ft. lbs.) . If not, replace the bolt.
2.4L * First All to 34 N·m (25 ft. lbs.) * Second All to 82 N·m (60 ft. lbs.) * Third All to 82 N·m (60 ft. lbs.) CAUTION: Do not use a torque wrench for the following step. * Fourth Turn an additional 1/4 Turn, 3.3L, 3.8L * Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.) * Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.) * Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.) * Step 4: Bolts 1 - 8 turn an additional 1/4 Turn. (Do not use a torque wrench for this step.)
The head bolt torque for a 1999 Chevrolet Tahoe 4-wheel drive 5.7 liter 8-cylinder in step one is 22 ft. lbs. For step two, tighten bolts 11, 7, 3, 2, 6, and 10 an additional 55 degrees. For step three, tighten bolts 12 and 13 an additional 65 degrees. For step four, tighten bolts 1, 4, 8, 5, and 9 an additional 75 degrees.
Use new bolts ! (each step involves tightening all bolts in the right sequence) Step 1 25 Nm Step 2 Angle turn 60 degrees Step 3 Angle turn 60 degrees Step 4 Angle turn 30 degrees Step 5 Warm up engine Step 6 Angle turn 30 - 50 degrees Tightening sequence cilinderhead bolts: 8 4 1 5 9 flywheelside 7 3 2 6 10 exhaust manifold: 25 Nm Inlet manifold: 22 Nm Valve-cover: 8 Nm
for v6: 8 5 9 12 4 1 13 11 7 3 2 6 10 Step 1) 22 ft-lbs (all) Step 2) Short bolts +55 degrees Medium bolts: +65 degrees Long bolts: +75 degrees
WWII in HD - 2009 Glory and Guts 1-8 was released on: USA: 18 November 2009