answersLogoWhite

0

Sure. 100% silicone can be used. The sealant is not necessary as the gasket does the sealing anyway. the sealant does help hold the gasket in place for easier installation.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

How do you Change a Car water pump?

for my 99 camaro, i had to find it first, then i took the belt off, then i took the bolts off and got a razor, and scraped the old water pump gasket off the water pump, then i put silicone gasket maker on my water gasket and put that on the water pump that is attatched to your engine, then i put silicone gasket maker on the new water pump and then i stuck that on the other half of the water pump and bolted it back on, lol i figuered it out by myself and im 16 and that is the first time i worked on my car, hoped that helped


We're repairing a water leak behind the timing cover of a 97 dodge PU the cover to engine side not the water pump side Is there a gasket or do we just use silicone around the water jackets?

No, there is a gasket.


Do you need sealant or Silicone with the gasket when changing the water pump in a 1994 Chevy Astro Van - 4.3L?

its a very good idea


Could antifreeze be leaking from the water pump gasket?

Yes, antifreeze can leak from a water pump gasket.


What sealant to use when installing a water pump?

I just installed a water pump on a 1997 Chevy Lumina and used Permatex Water Pump and Thermostat Housing RTV Silicone Gasket. Gel or paste in a .5 oz tube. Got it at ORilleys Auto Store. I don't like to install gaskets without something on them, just in case. I used a single edge razor blade to remove the old gasket material. You have to be careful not the damage the gasket face on the Engine water pump housing.


Where is the thermostat located and how do you replace it on a 1989 Nissan Sentra?

To Replace the thermostat if you follow the water pump toward the back of the engine. The thermostat housing is located right before all of the coolant hoses go into the water pump it is held onto the water pump with 3 bolts with 10mm bolts. the best way is to remove the three bolts and take out the old thermostat and scrape away the old gasket material. then take gasket and new thermostat and put rtv silicone around the top of the thermostat ( I recommend using the 1 minute silicone) then slip the thermostat into thermostat housing. Next take gasket and coat with silicone on both sides of gasket. then slip it in and finger tighten the three bolts. let set for 1 minute or 12 to 24 hours if 1 minute silicone is not used then torque down to appropriate specs don't overtighten


How do you remove the gasket off a water pump?

Just scrape it off with a scraper or a knife but be careful not to gouge the metal. If someone has made a silicone gasket instead of a fibre gasket, you might have to use a sharp edged knife to cut it off, and then scrape it to remove the rest.


When replacing the water pump on a 1994 crown Victoria do you need a gasket?

I was looking at fordparts.com and it shows a water pump gasket


What would cause a leak behind the water pump on a 1998 2.5 Chrysler Sebring?

Water pump gasket, head gasket, water tube,


What causes a leak at the water pump on my Nissan altima?

more than likely it is the water pump gasket,it probably has a tear in it or just dry rotted from age and use or if it is leaking out of the water pump itself it is the seal inside the water pump itself if this is the case the water pump must be replaced if it is the gasket just replace the gasket ...


How do you replace the water pump on a 1995 Oldsmobile Ciera?

If it is a 3.1 it is not hard to do i did one in 20 min. If you stand in front of the car on the passanger side follow bottom radiator hose that is the water pump. There are 4 or 5 bolts holding the pully on do not take belt off yet. Break looses the bolt's first. Pull the pully off there will be at least 4 bolts holding the housing on remove them you will loose about a glass of water. Pull the old water pump out and put new one in make sure you use blue silicone or something similar for water put silicone on water pump make sure holes line up on the gasket when you put it on the pump let sit for 5 min. put silicone on other side of gasket put it right one don't let site reassemble everything and your good to go.


How do you replace the water pump on a 1985 Buick Regal?

Remove all accesorie belts, fan and fan clutch then remove all bolts on water pump clean area with wire brush and aply hi temp silicone to both sides of gasket and torque youre new water pump to 20-35 pounds