answersLogoWhite

0

Yes, you can heat a pool after using copper algaecide, but it’s advisable to wait at least 24 hours to allow the algaecide to disperse and bind properly. Heating the water immediately after application may reduce the effectiveness of the algaecide. Always follow the manufacturer's instructions for optimal results.

User Avatar

AnswerBot

2d ago

What else can I help you with?

Related Questions

Why do you get heavy algae growth in your pool a day or two after using algaecide?

I just had a similar problem so I'll tell you what cleared mine up. I wasn't using enough Algaecide in my pool to correct the problem. I have about 32,000 gallons and the pool company recommended a quart and a half of an algaecide with 7% copper. I found mine at WalMart and it only had 3% copper, but it worked fine. Some of the products do not contain copper, they informed me, and copper is a necessary ingredient to kill the algae. Pour it in and let it sit overnight. Then vaccumm to WASTE the walls and bottom. The algae is so fine that it will remain in your filter and keep flowing back to your pool if you vac the pool in the normal way. The Copper ingredient bonds to the algae for removal. After the pool is clean, add a few ounces of the algaecide each week. I need to add about 6 oz. Let us know if this works for you.


Can you recommend a good algaecide for getting rid of black algae?

add a poly 60 or a 7% copper based algaecide if you dont have a heater on the pool.


Do saltwater pools have copper?

Any pool can have copper. Source water may have it in it. Some pools have copper plumbing. Most pool heaters have copper heat exchangers. If your pH or Alkalinty levels are lower than recommended, then the copper in the plumbing or heater can be stripped out and stain the pool plaster a bluish-green color. Some allgaecides even use copper which will also stain. You should also take care using copper algaecide in salt water pools as they may cause problems with the chlorinators.


Will shocking your foggy pool make it clear?

It might otherwise use a copper based algaecide at the same time and that should do it.


Can you use copper sulfate in swimming pools?

yes, just don't use too much I would not recommend using copper sulphate in a pool. It is an algaecide but it stains pools and is what causes hair to turn green. There are better algaecides available. It is not a sanitizer and is not a substitute for chlorine or bromine.


Is it safe to use copper triethanolamine pool algaecide for cleaning algae and mold on a concrete patio and how should it be diluted?

Copper triethanolamine pool algaecide should not be used on concrete surfaces as it can cause staining. Instead, consider using a bleach solution (1 part bleach to 4 parts water) to clean algae and mold on concrete patios. Always test on a small, inconspicuous area first to ensure it does not cause any damage.


If you put algaecide directly into swimming pool without mixing in a bucket of water first will it eat the paint away?

You don't have to mix the algaecide in a bucket of water, you can put it directly in the pool. I use Polyquat 60 that comes in quart bottles and add about 4-6 ounces per week. Just walk along the edge of the pool and pour it at the edge while walking. No algaecide will "eat the paint". It's not acid. In fact, all the algaecide does is strip the cell walls of the algae and make it more susceptible to the chlorine. It's the chlorine that kills the algae. However, one algaecide with a side effect of staining is Copper. It's a very effective algaecide, and it's safe - but it will stain concrete pools if it's used in a high enough concentration. And Copper can stain blonde hair as well. That's why I don't recommend using it. The preferred algaecide is Polyquat 60.


What swimming pool chemical besides chlorine kill trees?

Copper Sulfate, also known as Bluestone. Used as an Algaecide in commercial pools


May one use pool copper algaecide on koi pond?

I've personally never tried the chemical or heard of anyone that has, but heavy metals, such as copper, is not healthy for fish. Many types of pool algaecide are formulated to kill all living organisms in pools from algae to larvae. So it would stand to reason this would not be ideal for fish.


Can you use copper sulfate in your pool and how much?

Yes, copper sulfate can be used in pools as an algaecide to control algae growth. The recommended dosage for copper sulfate in pools is usually 0.2-0.4 ppm (parts per million), but it's important to carefully follow the manufacturer's instructions for the specific product you are using. Overuse of copper sulfate can lead to staining of pool surfaces and hair discoloration.


What do I do I put 10 times the dose Algaecide in my pool pool?

I suggest you contact the manufacturer of the algaecide and find out from them what would be the bes coarse of action.


How do you get the green out of your pool?

By killing the green algae with an algaecide available at your pool shop.