0
What else can I help you with?
How can you vacuum the bottom of an above ground pool out with out losing the water?
If you have the regular set up that includes a skimmer, pump and filter then you don't have to waste any water. Get an lid-to-hose adapter, that fits over the skimmer basket at your pool supply store. Fill the hose with water and attach it to the lid. Place the lid inside the skimmer over the skimmer basket, then vacuum to your hearts content. Pool Masters
How do you replace the poo skimmer door?
Drain the pool until the water level reaches two inches below the skimmer faceplate , remove the face plate using a screwdriver , remove the faceplate and skimmer , then replace the gasket and attach the skimmer and then the faceplate
How do you remove top of Samsung j1043 front loader?
Remove 2 screws from the back holding the top lid, then slide the lid backwards and lift the lid.
How do you remove center console lid for 2005 Chevy Trailblazer?
To remove the center console lid for a 2005 Chevy Trailblazer, you will first need to locate and remove the screws or bolts holding the lid in place. These are typically found underneath the lid or inside the console compartment. Once the screws are removed, you can carefully lift the lid off the console. Be sure to disconnect any wires or cables attached to the lid before fully removing it.
How can I get frogs out of my skimmer line on my inground pool?
You can buy a devise called a Jeanie Jet and it connects to your water hose. Take the lid off your pump and insert it into the front of the pump going back to the skimmer. You then turn on the water and it should blow out the line and unclog it. What comes out of that line will come out into the skimmer so watch for it.
Can you replace the skimmer without replacing the liner?
Yes you can. Drop the waterline in the pool below skimmer level, dig a whole around your skimmer to gain access. Unscrew the skimmer faceplate and remove it as well the old gasket. You also have to remove the second gasket between liner and wall. Detach the pipe(s) from the skimmer. Now install the new skimmer by attaching the pipe(s) to the skimmer put new gaskets in place screw the faceplate back on and you're done. Don't forget to fill your hole again and put water back in the pool to the appropriate level. ;-) Jens Poseidon Pool Services, Dunrobin, ON
How can you remove a wheelie bin lid?
you cant
How does hot water make a lid easier to remove?
The hot water expands the lid slightly.
How do you remove the rear speakers in a 2005 Nissan Altima?
u have to remove the rear deck lid, speakers r underneath how do you remove the rear deck lid on the 2005 Nissan altima
How can you remove ashtray on BMW 316 Compact?
pop up the lid, with the lid in the open position gently push down on the top edge of the lid that is facing you. The ashtray then pops up and you can then remove it, easy peasy.
How do you vacuum a Doughboy and where do you plug in the equipment?
In order to vacuumn the pool you must first put in the vacuum and the hose. You can siphon the air out of the hose by putting it in front of the return to dispace all air in the hose line. Then turn off the pump. Insert the end of the vacuum line either into the port at the bottom of the skimmer in the pool or remove the skimmer basket and insert it in the bottom of the skimmer. Then after the line is secure, turn on the pump motor. Your vacuum should be ready to use (manually) or run automatically if you have an automatic pool cleaner such as an Aquabug. If you have a slimline skimmer there is a port located just below the skimmer door it is used for the vac hose. After connecting the hose you put your skimmer lid down inside of skimmer and then you can turn on pump. By doing it this way you can let skimmer basket catch all large debries. This saves on having to backwash so much.
Your pool pump is working but it is not pumping water from the pool its like there is a blockage some where what could be the problem?
could be , is the water level above the skimmer/s / are the skimmer baskets clean/? pump may have just lost it's prime. fill pump with water replace lid and restart.
