0
What else can I help you with?
Do you run the pump after putting flocculent in?
When you put floculant in the pool you do not run the pump. you let the pool sit still for about two days. This will allow it to settle. After that time you will notice that there Is a cloudy area at the bottom of the pool. This is the floculant and all the contaminants that it has dragged down to the bottom as it settled. This will need to be vacuumed to waste DO NOT PUT THIS STUFF THROUGH THE FILTER,(VACUUM IT TO WASTE.) It's ok to pump it but not to run it through the filter.
What is the most efficient method for removing water from a pool using a pool water removal pump?
The most efficient method for removing water from a pool using a pool water removal pump is to position the pump at the lowest point in the pool, connect a hose to the pump, and then turn on the pump to suction out the water. This method allows for the water to be quickly and effectively removed from the pool.
How long does it normally take to drain the water from the pump when closing an in ground pool for the winter?
Draining the water from the "pump" (I'm assuming you mean the filter) should only take a few minutes. How long it would take to drain the water in the pool down to the winterization level would depend on the size of your pool and the pump you are using.
Replaced the pump in my above ground pool as it wasn't pushing out enough pressure for the vacuum now I have thick looking stuff at the bottom I don't think the auto vacuum will be able to move it.?
Have you used clarifier or flculent at any stage to clear the pool water. If you have the thick looking stuff is the clarifier or floculant settled on the bottom. The pool pump will pump this stuff only it is important not to put it through the filter as it will block it up in no time. Gently hand vacuum it to waste.
How do you flock a swimming pool?
1 Purchase a floculant from a pool shop 2 Turn of the pool filtration equipment 3 cast the floculant evenly over the surface of the water. 4 let pool settle for two days with the filtration turned of and the unit turned to waste you do not want this stuff to go through your filter. After a couple of days you will note that all of the water except for a layer at the bottom is beautifully clear. do not disturb the layer at the bottom any more then you have to. 6 gently lower a pool vacuum into the cloudy layer on the pool floor then start the pump which should be set to waste. Then vacuum all of this layer out of the pool. you will loose about 6"/150mm to 12"/300mm of water doing this.
How long should your pool pump in winter?
5 hours
Will chlorine ruin a well pump Example Using the well pump for a pool The pool is about 5000 gallons...?
its a low volume high preasure pump. there no good for a pool they dont have the flow and if is a cast iron pump it will bleed , so you will have rust streaks. but if its all ya got go with it.. your pool pump repair guy in longwood fl
How can I use a pump to efficiently drain my pool?
To efficiently drain your pool using a pump, connect a hose to the pump and place the other end in a suitable drainage area. Turn on the pump and allow it to remove the water from the pool. Monitor the process to ensure the water is draining properly and adjust the pump as needed.
What are the benefits of using a pool heater pump for maintaining the temperature of your pool?
Using a pool heater pump can help maintain a consistent and comfortable temperature in your pool, allowing you to enjoy swimming year-round. This can extend your swimming season, increase the value of your property, and provide a more enjoyable experience for you and your guests.
How can I properly hook up a pool pump?
To properly hook up a pool pump, first, make sure the pump is placed on a level surface near the pool. Connect the pump to the pool's filtration system using the appropriate hoses and fittings. Ensure the pump is securely connected to a power source and follow the manufacturer's instructions for priming and starting the pump. Regularly check and maintain the pump to ensure proper functioning.
How can I use a pump to efficiently remove water from a pool?
To efficiently remove water from a pool using a pump, you should first ensure the pump is properly connected to the pool's drainage system. Next, turn on the pump and adjust the settings to the appropriate flow rate for your pool size. Regularly monitor the water level and empty the pump's filter basket to maintain optimal performance.
How do I properly hook up a pool pump?
To properly hook up a pool pump, first, make sure the pump is placed on a level surface near the pool. Connect the pump to the pool's filter system using the appropriate hoses and fittings. Ensure the pump is securely connected and the hoses are tight to prevent leaks. Finally, prime the pump by filling it with water before turning it on to ensure proper operation.
