0
To remove the spool in a Weed Eater XT110, first, ensure the trimmer is turned off and unplugged. Press the tabs on the sides of the spool housing to release it, then pull the spool out of the housing. If necessary, you can also unwind any remaining line before replacing or refilling the spool. Always refer to the user manual for specific instructions related to your model.
What else can I help you with?
How do I perform a Ryobi weed eater string replacement?
To perform a Ryobi weed eater string replacement, first turn off the weed eater and disconnect the spark plug. Then, remove the spool cover and take out the old string spool. Cut a new piece of string to the appropriate length and thread it through the spool. Wind the string in the direction indicated on the spool and secure the ends. Finally, replace the spool back into the weed eater and reattach the spool cover.
How do I replace the line on my Ryobi battery-powered weed eater?
To replace the line on your Ryobi battery-powered weed eater, follow these steps: Turn off the weed eater and disconnect the battery. Remove the spool cover by pressing the tabs on the sides. Take out the spool and remove any remaining line. Cut a new piece of trimmer line to the appropriate length. Insert the line into the spool following the arrows for direction. Reassemble the spool and cover, then reconnect the battery. Test the weed eater to ensure the line is working properly.
How can I replace the string on a weed eater?
To replace the string on a weed eater, first, turn off the weed eater and disconnect the spark plug. Then, remove the spool housing and take out the old string. Cut a new piece of string to the appropriate length and thread it through the spool. Wind the string in the direction indicated on the spool and secure the ends. Finally, reassemble the spool housing and reconnect the spark plug before using the weed eater again.
How to change the line on a Ryobi weed eater?
To change the line on a Ryobi weed eater, first, remove the spool cover and take out the old line. Cut a new line to the correct length and insert it into the spool. Wind the line evenly and securely onto the spool, then reassemble the spool cover.
How do I remove the head of a Ryobi Expand-It weed eater?
To remove the head of a Ryobi Expand-It weed eater, you typically need to unscrew the bump knob or cap on the head of the trimmer. Once the knob is removed, you can access the spool and remove it from the head. This allows you to detach the head from the weed eater for maintenance or replacement.
How do you change the spool on a craftsman bushwacker weed eater?
I can't seem to get the spool off.
How can I restring a Ryobi Expand-It weed eater?
To restring a Ryobi Expand-It weed eater, first remove the spool from the trimmer head. Cut a length of new trimmer line, thread it through the eyelet holes on the spool, and wind it evenly in the direction indicated on the spool. Reattach the spool to the trimmer head and trim any excess line.
How do I restring a Ryobi Expand-It weed eater?
To restring a Ryobi Expand-It weed eater, first remove the spool from the trimmer head. Cut a length of new trimmer line, usually around 10 feet. Insert the line into the spool following the arrows for the correct winding direction. Secure the line in the notches on the spool and reassemble the spool onto the trimmer head.
What is the best way to replace a weed eater cord?
The best way to replace a weed eater cord is to first make sure the engine is off and cool. Then, remove the spark plug wire to prevent accidental starts. Next, remove the spool housing and old cord. Install the new cord by winding it onto the spool in the correct direction. Finally, reassemble the weed eater and test the cord before using it.
Which brand of trimmer has the fewest spool tangles?
The Weed Eater brand of trimmers have very few spool tangles
How do you wind new weed eater string on an old spool?
pull straight out to remove the spool, wind in the direction of the arrow - to replace, feed the string through the hole and pull on it, keeping slight tension on the spool as you push it back into the head
Do a electric weed eater have littke bb's in it?
No, electric weedeaters have a motor and a cord spool.
