answersLogoWhite

0

I can't seem to get the spool off.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How to change the line on a Ryobi weed eater?

To change the line on a Ryobi weed eater, first, remove the spool cover and take out the old line. Cut a new line to the correct length and insert it into the spool. Wind the line evenly and securely onto the spool, then reassemble the spool cover.


How do you load weed eater line on a craftsman?

To load weed eater line on a Craftsman trimmer, first, turn off the trimmer and unplug it if it's electric. Remove the spool from the head by pressing the tabs and pulling it out. Cut a length of trimmer line (typically around 10-15 feet), then insert one end into the spool's eyelet and wind the line in the direction indicated by the arrow on the spool. Finally, replace the spool back into the trimmer head and pull the line to ensure it feeds properly.


How do you change the spool on a craftsman weedwacker model 257796022?

To change the spool on a Craftsman Weedwacker model 257796022, first, make sure the trimmer is turned off and unplugged or the battery is removed. Press the tabs on the spool cover to release it, then carefully remove the old spool. Install the new spool by threading the line through the eyelets, then replace the cover, ensuring it clicks securely into place. Finally, wind any excess line if necessary and you're ready to go.


How do I perform a Ryobi weed eater string replacement?

To perform a Ryobi weed eater string replacement, first turn off the weed eater and disconnect the spark plug. Then, remove the spool cover and take out the old string spool. Cut a new piece of string to the appropriate length and thread it through the spool. Wind the string in the direction indicated on the spool and secure the ends. Finally, replace the spool back into the weed eater and reattach the spool cover.


Which brand of trimmer has the fewest spool tangles?

The Weed Eater brand of trimmers have very few spool tangles


How can I replace the string on a weed eater?

To replace the string on a weed eater, first, turn off the weed eater and disconnect the spark plug. Then, remove the spool housing and take out the old string. Cut a new piece of string to the appropriate length and thread it through the spool. Wind the string in the direction indicated on the spool and secure the ends. Finally, reassemble the spool housing and reconnect the spark plug before using the weed eater again.


Cant get the spool out of a craftsman line trimmer?

1. Rotate spool to line up arrows on spool and surrounding casing. 2. Find notch and pry with wide flat-end screwdriver. 3. Spool will pop out.


How do you remove spool in weed eater XT110?

To remove the spool in a Weed Eater XT110, first, ensure the trimmer is turned off and unplugged. Press the tabs on the sides of the spool housing to release it, then pull the spool out of the housing. If necessary, you can also unwind any remaining line before replacing or refilling the spool. Always refer to the user manual for specific instructions related to your model.


How do you change cord in weed eater rt112?

To change the cord in a Weed Eater RT112, first, ensure the trimmer is unplugged or the battery is removed for safety. Remove the spool from the trimmer head by pressing the tabs and pulling it out. Then, take the new line, cut it to the desired length (usually about 10-12 feet), and insert it into the spool, winding it in the correct direction. Finally, reassemble the spool back into the trimmer head and ensure it’s securely in place before use.


How can I restring a Ryobi Expand-It weed eater?

To restring a Ryobi Expand-It weed eater, first remove the spool from the trimmer head. Cut a length of new trimmer line, thread it through the eyelet holes on the spool, and wind it evenly in the direction indicated on the spool. Reattach the spool to the trimmer head and trim any excess line.


How do I replace the line on my Ryobi battery-powered weed eater?

To replace the line on your Ryobi battery-powered weed eater, follow these steps: Turn off the weed eater and disconnect the battery. Remove the spool cover by pressing the tabs on the sides. Take out the spool and remove any remaining line. Cut a new piece of trimmer line to the appropriate length. Insert the line into the spool following the arrows for direction. Reassemble the spool and cover, then reconnect the battery. Test the weed eater to ensure the line is working properly.


Change the spool of line on a weed eater SG11 Can't figure out how to get the original one off?

Locate the round tap button. Pull it straight out, firmly. This opens the chamber for new line or spool. I figured this out five minutes ago.