0
What else can I help you with?
How do you remove the bolt from a Marlin Glenfield Model 20 rifle?
Open the bolt, pull it to the rear, hold the trigger back and remove the bolt. sales@countrygunsmith.net
Do you need to remove the original rear site in order to use a peep sight?
you do for a marlin or mossberg
How do you get the rear sight off a marlin model 75?
To remove the rear sight from a Marlin Model 75, first ensure the firearm is unloaded and safe to handle. Locate the screws securing the rear sight to the receiver; typically, there are two screws on either side. Use a suitable screwdriver to carefully remove these screws. Once the screws are out, gently lift the rear sight off the dovetail or mounting area.
Where can you buy a rear sight assembly for 22 caliber bolt action Glenfield-Marlin single shot model 10?
You can purchase a rear sight assembly for a .22 caliber Glenfield-Marlin single shot model 10 from various sources, including online retailers like Brownells, MidwayUSA, or Numrich Gun Parts. Additionally, you may find parts on auction sites like eBay or through firearms specialty shops. For more specific or hard-to-find parts, consider visiting local gun shops or checking with gunsmiths who might have access to spare parts.
Marlin 55 Goose guns have 2 threaded holes in the rear of the receiver what are they for?
Peep sight
Where can you find rear sight for a Marlin model 98?
Numrich gun parts corp.They may be found on the web.
What are the specifications of a Glenfield model 60 22 rifle?
According to my owner's manual for the Marlin Glenfield autoloaders 75C and 60, the model 60 specs are as follows: Length: 40 1/2", Weight: 5 1/2 lbs., Barrel: 22", Front sight: Ramp, Rear sight: Adj. open, Mag. Type: Tubular, Stock: 1 pc. walnut-finish hardwood, Ammunition: .22 L.R., Mag. Capacity: 18. Manual dated 1975.
How do a adjust the sight on your marlin glenfield model 30?
Factory sights? The rear sight elevation is accomplished by gently lifting the back of the rear sight and sliding the ribbed elevator back or forward to raise or lower the impact of the bullet. Move the rear sight in the direction you want the bullet to go. Up for higher, down for lower. The windage( left or right) is accomplished by drifting the rear sight in its dovetail slot with a hammer and brass drift punch. Put duct tape on the sight or use a small piece of leather between the punch and the sight to prevent damage.. go slowly, a little movement of the sight moves the bullet a lot at 100 yds. Move the rear sight in the direction you want the bullet to go. On some rifles, the front sight insert can be moved side to side in its base. A special tool called a sight pusher prevents damage to the small insert. You move the front sight the opposite of the way you want the bullet to go.
When was a marlin model 55-12 serial?
behind the rear sight bracked on the left side just above the stock
How do you remove the rear sight on a M1 carbine 30?
I believe the serial number is behind or to the rear of the rear sight. you should be able to see serial number without removing sight
How do you remove the rear sight of a Remington 742 rifle?
To remove the rear sight of a Remington 742 rifle, first ensure the rifle is unloaded and safe to handle. Use a flathead screwdriver to carefully loosen the screws securing the rear sight to the receiver. Once the screws are removed, gently lift the sight off the mounting base. Be cautious not to damage the sight or the receiver during this process.
How do you turn on the safety on a glenfield marlin model 60?
To engage the safety on a Glenfield Marlin Model 60, locate the safety lever, which is typically found on the rear of the receiver. Push the safety lever to the right to engage it, which will prevent the trigger from being pulled. When the safety is engaged, a red dot will usually be hidden, indicating that the firearm is safe. Always ensure the safety is on when not in use or when handling the firearm.
