0
To replace the pull string on a Toro weedeater, first ensure the engine is off and cool. Remove the starter cover by unscrewing any screws, then take out the spool containing the old string. Thread a new string through the spool, wind it tightly in the direction indicated, and reassemble the spool into the housing. Finally, reattach the starter cover, and your weedeater will be ready for use.
What else can I help you with?
How do you replace a Toro weedeater pull string?
you would take off the cover and expose the recoil spring/shaft then detach the string and put the new one on
How do you open the head to a weedeater to replace string?
On most of them you hold the top part with one hand and turn the bummer/spool clockwise (looking from the top)and pull it straight down/outward
How do you replace the pull string on the Bolens BL110 gas trimmer?
how to replace pull wrope on bolens bl110
How can I replace the pull string on a light fixture?
To replace the pull string on a light fixture, first turn off the power to the fixture. Remove the old pull string by unscrewing the fixture cover and disconnecting the old string. Attach the new pull string by threading it through the fixture and connecting it to the switch mechanism. Secure the fixture cover back in place and restore power to test the new pull string.
How do you replace string on craftsman weedeater model 358.795550?
Unplug the weedeater from electrical source. Turn the weedeater upside down and remove the black knob on the bottom. If the black knob won't come off you can carefully use a large pipe wrench and turn it counter clockwise to loosen it. Be careful not to lose the slotted metal ring between the black knob and the trimmer spool. Remove the spool and clean it off. There is an arrow showing you where to insert the string. Start pushing the line into the spool going counter clock wise. Be sure to use only .065 ROUND string. Put the spool back on the spindle yellow side up. Hold the slotted metal ring with the slot facing up. Insert the string into the bottom of the ring and put the ring in the recessed circle on the spool, (yellow side). Pull the string over the slot and hold it there. Screw the black knob back onto the spindle, making sure the string is in the slot on the metal ring. Tighten the knob. You are now ready to go.
Your weedeater lawn mower cord wont pull?
get a new one
How do you replace pull cord on gbi 22v weedeater blower?
To replace the pull cord on a GBI 22V weedeater blower, first, remove the starter cover by unscrewing the screws holding it in place. Take out the old cord from the starter assembly and measure a new cord to the same length, then thread it through the starter pulley and tie a knot to secure it. Wind the new cord around the pulley, then reattach the starter cover and ensure everything is tightened properly before testing the pull cord.
How can I fix a pull string light that is not working properly?
To fix a pull string light that is not working properly, you can start by checking the light bulb to see if it needs to be replaced. If the bulb is fine, you can then check the pull string mechanism to ensure it is not damaged or stuck. If the issue persists, you may need to replace the pull string switch or seek professional help to diagnose and fix the problem.
How do you wind new weed eater string on an old spool?
pull straight out to remove the spool, wind in the direction of the arrow - to replace, feed the string through the hole and pull on it, keeping slight tension on the spool as you push it back into the head
How do you remove broken off flexible drive shaft from weedeater?
remove head pull shaft out
What is the string that you pull to turn on a ceiling light called?
The string that you pull to turn on a ceiling light is called a pull chain or pull string. It is typically connected to the light fixture and used to control the on/off function of the light.
How do you replace guitar strings?
As you pull off one string, replace it immediately with another, so you don't get confused. The 1st string is the high E or thin string at the bottom. Go in order 1,2,3,4,5,6. When winding the string make sure on the high strings you go under on the first turn so the rest of the string clamps down. If you do enough turns however, this may not be necessary. Just make sure the string is tight.
