answersLogoWhite

0

An Impact wrench is for a totally different use. A torque wrench will let the user know when a certain torque has been achieved in tightening. The impact wrench is for removing very tough nuts under impact of a hammer.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

What is the best way to properly tighten bolts on a Canyon bike using a Canyon torque wrench?

To properly tighten bolts on a Canyon bike using a Canyon torque wrench, follow these steps: Ensure the torque wrench is set to the recommended torque level specified in the bike's manual. Insert the appropriate bit into the torque wrench. Place the bit on the bolt and apply steady pressure while turning the wrench until you hear or feel a click, indicating the bolt is properly tightened. Avoid over-tightening the bolts, as this can damage the components. Repeat the process for all bolts on the bike.


Are you supposed to torque bolts or nuts?

It depends on the application, if you are speaking generally.If you meant for applications where the bolt and nut are both present, and specific torque specifications are required, it really doesn't matter. Whichever is best accessible by the torque wrench. The only stipulation is that whichever item the torque wrench is not being used on, must be static (unable to turn). For example, if you are torquing the nut, the bolt must not be able to turn (held in place with a wrench, if necessary) while the torque wrench is being read, for a reading to be accurate.


What is the best tool to use to remove the CV axle nut?

Honestly, a 1/2 in. impact wrench, with the impact socket that fits the nut. Could be a 28mm,30mm,32mm... or so. Use a torque wrench to install the new nut--over tightening can lead to bearing damage. Don't forget to punch the notch in on the nut to lock it in place. Use a new nut if possible. There's only about 90 lb-ft of torque on one of these nuts, so a socket on an 18" breaker bar works fine.


What size torque wrench to remove cavalier front bearing?

A torque wrench is not required to remove the bearing. It is required to apply the correct loading to a nut or bolt when assembling. Because the fixture may have been in place for some time a greater force may be needed for removal, because of corrosion or dirt, than the original torque setting applied.


Where can I purchase a hydraulic torque wrench online?

If you're looking to purchase a hydraulic torque wrench online, it’s crucial to buy from a trusted supplier who offers genuine tools, competitive pricing, and full after-sales support. Not sure where to start? We’ve created a complete guide to help you choose the right hydraulic torque wrench supplier, understand key quality features, and secure the best deals directly from manufacturers in India. Read the full guide here: Top Hydraulic Torque Wrench Suppliers & Manufacturers in India (Get expert tips, industry insights, and contact details in one place!) Don't just buy online buy smart with guidance from industry professionals.


What is the torque for the pinion nut on a 68 Camaro 10-bolt rear end?

There are a couple different methods to correctly torque the nut on the pinion. One way that I have used in the past with excellent results,is to tighten the pinion nut real good and snug just as you feel the crush sleeve begin its resistance,and then you actually place an "inch pound" torque wrench(Dial or Bar style tends to be a little quicker and more exacting than a click style) with correct socket on pinion nut and rotate the pinion by way of the smaller torque wrench (ring gear and carrier removed).If the inch-pound torque wrench doesn't click before the pinion rotates(inch-pound wrench set approx @12-15),then snug the pinoin nut up with your 1/2 drive impact more.Tighten nut in SMALL increments.Dont overshoot it,other wise you run the risk of wasting the one time use crush sleeve and burning up the pinion bearings.If say the wrench clicks @10,11,12ish before the pinion rotates,but if set @ 15 or so,and the pinion rotates before the torque wrench clicks, you are in the right area.What you are doing is measuring the amount of "rotational drag" on the pinion with the inlb torque wrench.Another way is if the crush sleeve is replaced with a solid spacer,the nut can be torqued down with a regular pop wrench to about 60-75 ft/lbs.


Where is the best place to keep a pet fox?

easy...you shouldnt have one


How do you replace a pulley on a water pump on a 1989 Chevy Celebrity?

There should be a place for an Allen wrench to be inserted into the end of the water pump shaft, and a flat place for a spanner wrench on the pulley itself. An impact wrench may be required to break it loose, they can be very tight. Also, be aware of thread orientation. It also may be pressed on, if so you will need a puller to remove it.


Can you take cialis while on thyroxin?

you shouldnt have been on cialis in the first place


Where is the best place to rent a hydraulic torque wrench?

I suggest MaxPro Rentals. They offer a wide variety of hydraulic torque wrenches. They will rent and ship to anywhere in the world and can usually ship the same day. Get more info here: http://www.maxprocorp.com/store.asp?pid=25736


Why is it easier to turn a bolt with a wrench?

The longer handle gives you more leverage. You use Force to push or pull an object in an attempt to make it move. When you want to cause something to rotate (tighten or loosen a nut for example), you need Torque. Torque = the force you apply to your spanner times the distance your hand is from the nut you are trying to turn. Thus, if you have a longer spanner, you can place your hand farther from the nut and the Torque on the nut will increase. You have to be careful about long handled wrenches or slipping a piece of pipe over a wrench to make it longer as you can generate so much Torque that you can snap the bolt clean off or strip the threads. If you have to tighten a nut/bolt very firmly, but don't want to strip/snap it, you can use a Torque Wrench. It has a gauge that tells you how much Torque you are applying to the nut/bolt so that you can tighten it to specifications without going over.


What is the proper way to tighten a bicycle stem bolt to ensure the safety and stability of the handlebars while riding?

To properly tighten a bicycle stem bolt for safety and stability, use a torque wrench to tighten the bolt to the manufacturer's recommended torque specification. This will ensure that the handlebars are securely in place while riding.