answersLogoWhite

0

Snow load depends on geographic location, not on roof pitch. Most of Washington falls into the 25 psf snow load. Snoqualmie, for example, has a 50 psf snow load since it receives a higher amount of snow fall than an area such as Seattle. Your county building department can answer this question for your specific location and/or has a snow load map where you can look it up yourself.

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

4-12 pitch roof and 65 pound snow load how deep dry powder snow is safe?

A 4-12 pitch with a 30lb snow load will hold approximately 6 feet of wet snow. If you went to a 40lb-snow load and kept the roof pitch at 4-12 your roof would be able to hold 8 feet of wet snow. We don't get that much dry powder in New England...:)


What is the snow load for Troy Montana?

The snow load for Troy, Montana can vary depending on the specific location and elevation within the town. It is recommended to consult local building codes or a structural engineer to determine the snow load requirements for a specific site in Troy, Montana.


What is the roof snow load for forks Washington?

The roof snow load for Forks, Washington falls within the range of 40-60 pounds per square foot, given the region's location experiencing heavy snowfall. However, it is advisable to check with local building authorities or a structural engineer for the most accurate and up-to-date information for specific building requirements.


What is the ground snow load psf in Alberta Canada?

The ground snow load in Alberta, Canada varies depending on the location, but it is typically in the range of 20-30 pounds per square foot (psf) for residential areas. It is recommended to consult the National Building Code of Canada or local building authorities for specific information on snow load requirements in Alberta.


How do you calculate the weight of snow on a pitched roof?

Surface area of the roof times depth of snow gives volume of snow. Take a sample of snow and weight it to determine density (since the density of snow can vary quite a bit). Density times volume equals weight.


What is the snow load for Portland Maine?

The typical snow load for Portland, Maine varies, but it is generally around 40 pounds per square foot. This can increase during heavy snow seasons or in areas with high accumulation. It is important to consult with local building codes and regulations for specific requirements.


What is the snow load for Jefferson county Missouri?

From the USDA Forestry Division, they say the snow load for Missouri is 10-20psf. I would reccomend going with the higher of those


How do you decide the pitch of your roof?

Sometimes its looks over function that determine the roof pitch. Are the mechanicals in the attic or the basement? What part of the country, snow/rain load. Sometimes the span will determine how high the ridge ends up. Sometimes the cost comes into play.


What is the snow load for a 1975 champion double wide mobile home?

The snow load for a 1975 Champion double-wide mobile home would depend on the specific location and the building code in that area. It is recommended to consult local building authorities or a structural engineer to determine the appropriate snow load requirements for the specific site.


What standard building techniques are used to ensure that structures can withstand force placed upon them egthe force from the weight of snow on a roof?

Standard building techniques to ensure that structures can withstand forces like snow loads on a roof include using appropriate roof pitch angles to allow snow to slide off, reinforcing roof framing with trusses or rafters, and ensuring proper insulation to prevent ice dams. Additionally, engineers may specify snow load calculations and structural design requirements to meet building code standards for snow load resistance.


What is the weight of snow load?

The weight of snow load varies depending on factors such as snow density and moisture content, but a common guideline is that fresh, powdery snow weighs about 5 to 15 pounds per cubic foot, while wet, heavy snow can weigh between 20 to 30 pounds per cubic foot. Building codes typically require consideration of specific snow load values to ensure structural safety, which can be significantly influenced by local climate and historical snowfall data. It is crucial for engineers and architects to account for these factors when designing structures in snow-prone areas.


Is the roof of a home considered a load bearing structure?

Yes, the roof is a load bearing structure. Wind, rain and snow all apply loads to a roof. Snow loads can be very great in some portions of the country