0
Do you need to put a shunt resistor to connect the ac voltmetr?
Wiki User
∙ 10y ago
Shunt resistors are used with ammeters; voltmeters require series resistors.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
Why do you find out capacitor before shunt resistor?
I need answer of this question plz as soon as possible
Why shunt resistance is connected in the parallel?
Shunt means parallel only..................
Why you use 250 Ohm resistor in series with HART protocol communication?
You need to use the 250 Ohm resistor in series with HART protocol communication because it acts as a shunt resistor.
Ism there 0 ohm resister available in market then its colour coding what?
Why would you buy something that does absolutely nothing? If you need a "zero ohm resistor", just don't connect any resistor at all.Why would you buy something that does absolutely nothing? If you need a "zero ohm resistor", just don't connect any resistor at all.Why would you buy something that does absolutely nothing? If you need a "zero ohm resistor", just don't connect any resistor at all.Why would you buy something that does absolutely nothing? If you need a "zero ohm resistor", just don't connect any resistor at all.
How do you connect 480volt and coil to fire alarm system?
I can only assume that you are attempting to connect 480VAC coil from a elevator to a fire system in order to shunt the elevator. In order to do this you will need a shunt trip breaker rated for this use.
Why you need to connect resistor in series for the practical voltage source?
A resistor is connected in series with a practical voltage source in order to determine the current produced by the source.
How do you reduce 48 volts dc to 12 volts dc with resistors?
Yes. You can use a voltage divider. Say, for instance, one 1KOhm resistor in series with a 3KOhm resistor. Connect the 3k resistor to the 48 volts and connect the 1k resistor to ground. The 1k resistor will have 12 volts acress it. These resistors need to be at least 1 watt each as they are going to dissipate 0.576 watts and get warm. Now, if you attempt to pull power from the 1k resistor, note that regulation will be poor because the impedance of the load will go in parallel with the 1k resistor and change its value.
How do you replace a blower motor resistor for a 2002 Mitsubishi Lancer?
the blower motor resistor is located behind the blower motor which is located behind the glove box there is clip wires you need to disconnect and then connect the new one.
Can you use T12 lamp holders with T8 lamps when you change to T8 ballast?
Absolutely. Only you need connect together two wires coming from each lamp holder (shunt).
How is a Tee Cardiac Shunt preformed?
A TEE is a transesophageal echo, which is a diagnostic test. A cardiac shunt is a separate thing altogether, as it is surgery. Perhaps they performed a TEE and as a result, felt there was a need to proceed further and explore the need for a shunt?
How do you hook up wire from ansul system to shunt trip breaker?
You would need to take the "input" wire for the shunt trip breaker to an electrical switch (not alarm initiating switch, which are DC voltage rated) within the Automan unit and connect to the "Common" connection and the "return", the wire to the actual shunt circuit of the breaker, from the "Normally Open" connection of the switch. When the unit activates, the switch will be placed into "Closed" position, therefore completing the circuit and activating the shunt coil.
What is called when a child has value shunt caused of water in the brain?
The shunt used for a person who has hydrocephalus ("water on the brain") is not called a "value shunt". It is usually called a "ventriculo-peritoneal shunt" or "VP shunt" for short. Sometimes a "ventriculo-atrial shunt" or "VA shunt" is used instead.
