0
Go to YouTube and type in 6.5hp governor removal or you can also type in preparing a box stock engine. I removed the governor on mine completely and with a smaller rear sprocket it manages almost 60mph now. The governor doesn't let the engine rev over 3600rpm, with it gone it will rev to 6000rpm. If you don't have the mechanical skill to remove it completely you can bypass it. Replace the long spring that goes from the governor arm with a solid rod. So now you will have two rods on the governor arm and no spring. That works just as well as removal.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you remove the governor off a Baja 90cc?
To remove the governor off a Baja 90cc refer to your owners manual. Many newer models do not have a governor.
Who is the president of baja California sur Mexico?
Baja California is a federal state that is part of Mexico. It doesn't have a president per se, but a governor. Current Baja California governor is Jose Guadalupe Osuna Millan (term: 2007-2013).
What type of engine does a baja heat mini bike have?
The Baja Heat mini bike has a 200cc 6.5 Hp size engine.
How do you take the govenor off a Baja dr150 and is there performance parts for it?
There is no governor and no perf parts.
Gaspar de Portolá when was he born?
He was of noble birth, born in Catalonia. In 1767. As the Governor of Baja California, was responsible for expelling the Jesuits from Baja California. The Baja California missions were later turned over to the Franciscan the Dominicans.
What is the address of the Governor of Baja Sur?
The governor of the Mexican state of Baja California Sur resides in the capital city of La Paz. The governor's palace is on the main street, named Isabel la Catolica. Contact Information : Palacio de gobierno (Isabel La catolica) C.P. 23007 La Paz Baja California Sur - MEXICO Tel: (52-12) 223 92 / 207 82 / 294 77
How do you take the governor off a Baja Bug?
You can adjust it, by turning out the "Engine Governor Speed Adjustment" Screw. Check out the doodlebug manual, or message me for more details.
How can you make a baja racer minibike faster?
Loosen the governor which is a screw behind the front chain cover. Search on YouTube,"How to make a Baja racer mini bike go faster."
Where is the governor located on a baja doodle racer?
near the other end of the throttle cable where it lets in the gas.
How was baja California formed?
It was Formed by the Reaction of the Volcanism 600F under the earths surface where the heat and pressure rose all the Lava and formed the Baja California
Does Governor Marcos Alberto Covarrubias Villasenor of the Mexican state of Baja California Sur support or oppose the legalization of same-sex marriage?
Indifferent. Same-sex marriage is recognized but not performed in the state of Baja California Sur.
How do you adjust the governor screw on a Baja Doodlebug?
There is no "governor screw" on a doodlebug. There is a throttle stop screw. If you look at the side of the carburetor you will see a small screw with a spring around it, back that out until the throttle lever no longer touches it when the throttle twisted grip is at full throttle. That won't give very much of an improvement though, because the real governor is still working. To bypass the governor, which limits the maximum revs of the engine you need to go one stage further (which will almost double the top speed of the bike). When you turn the throttle you will see that the cable pulls on a small lever behind the carburetor. If you raise the rear wheel of the ground (so that you can rev the bike without it moving forwards) you will see that when the engine reaches roughly 3600rpm the governor engages. You will see that there is an arm connected to a shaft that comes out of the front engine casing just below the carburettor. That is the governor. That is directly connected to the carb with a long thin steel rod. When the engine reaches 3600rpm that rod closes the butterfly on the carb, restricting the maximum revs to 3600rpm. You need to bypass this mechanism. Attach the governor arm to the throttle arm with a zip tie. This will stop the governor arm from engaging. The engine will rev to about 5300rpm (it's natural limit) instead of 3600rpm. You will see a corresponding increase in your top speed. If you search youtube you can find a video of someone doing it to a mini Baja 6.5hp. Although the engine is a slightly different design, the governor works in exactly the same way. On the Doodle bug the governor arm and throttle arm are located vertically on the front of the engine, on the Baja Warrior/Heat/MB200 it is horizontal, but it works in exactly the same way. Search for Baja Warrior Mini Bike Easy Governor Bypass. There are several different videos showing how to do it, from using a piece of wire to using a zip tie to using a fishing line to do it. They all do the same thing though. They are all for Baja Heat/Warrior/MB200, but as I said, they all work for the Doodle Bug too.
