Unanswered | Answered

Hydraulics

~1300 answered questions
Parent Category: Engineering
Due to its immense power, hydraulics are used for operating various machinery, vehicles, aircraft, ships and equipment. The data and engineering revolving around hydraulics is so vast, its hard to comprehend.
%DETAILS% Thanks for the info. My top doesn't always go down, but of course today when I took it to the dealership it worked. Where do I find the conv. motor? (I've only had the car a couple of months.) 98' Mustang   Not sure if your motor is the same as mine ('71 Cutlass), but mine says t…
Popularity: 187
Chrysler Sebring Convertible Fluid Fill with hydraulic fluidA. On top of one end of the convertible top pump is a rubber fill plug, remove it and fill it to the bottom of the fill hole. Here is the proper procedure.Rotate and raise the motor/pump assembly so the reservoir is in the up position. The …
Popularity: 79
unfortunately Saturn went out on a limb to produce easy swappable parts in their cars. the clutch hydraulic system can not be bleed. it was intended on being replaced as an entire unit, filled with fluid and bleed at the factory. I've made many trips the salvage yards to obtain a entire assembly.
Popularity: 70
try to bleed the clutch
Popularity: 64
Get a manual on your car from AUTOBOOKSONLINE.COM or DISCOUNTAUTOREPAIRMANUALS.COM
Popularity: 42
To repair ABS hydraulics locate the ABS modular unit and drain the brake fluid. Close the bleeder and turn off your engine, then refill the reservoir.
Popularity: 61
You put a manual selector valve in between you spool valve and your outlet,turn handle to chose ,costs about $60.Nothing hydraulic is cheap; however, if you buy a double hydraulic control and appropriate hoses, that is the cheapest way to go.You can get a T-piece and fit it into your existing outlet…
Popularity: 68
All you have to do is let it gravity bleed. Just open the bleeder valve on the transmission and have someone watch the fluid level in the resavore.It might take a few minutes but that's the easiest way that I have found.
Popularity: 36
The hydraulic clutch line reconnects by just pushing it into the connection it came out of on the slave cylinder. You should hear a click when it is in place. The clutch will not depress if the line is not fully inserted into the slave cylinder. There are little metal "fingers" inside of the connect…
Popularity: 42
There is a bleeder nut/valve (8mm) on the master slave which is located on the front of the transmission you'll need 2 people have some one press all the way down on the clutch and have the other person open and close the valve and keep doing it only keep the valve open for a second though until all…
Popularity: 49
push in on line and push the plastic bushing that is on the connector up inside the connector itself to release it.
Popularity: 31
Check your firewall, I have seen them break or 'stretch' causing grief for clutch action.
Popularity: 86
Most bleed proceedures are the same. Have an assistant push the clutch pedal all the way to the floor and hold it there. Then loosen the bleed valve on the slave cylinder under the vehicle.This is the device which disengagesthe clutch. Now check the fluid level. Usually there is a seperateresevoir f…
Popularity: 24
Answer My 2.3 is hydraulic Audis have a hydraulic clutch system, with a master cylinder (in car on firewall) and a slave cylinder (outside on transmission) with a metal tube between them (which looks like a brake line).
Popularity: 55
Fill the clutch resivoir with fluid, and make sure it stays that way while you open the bleeder screw on the slave cylinder and allow it to gravity bleed until all bubbles are out.answerpump pedal 1 2 3 4 to the floor hold,other person open screw on slave cylinder tssssit close screw then release pe…
Popularity: 33
in the clutch kit u get a easy disconnecter tool that u slip in between the plastic slip guard and the metal piece and pry up don't cut the line hard as hell 2 find
Popularity: 37
Which are you referring to? Brakes or manual transmission slave cylinder?Either way, you need to find the bleeder. You will more than likely need a second person to help you.Get a manual on the vehicle for more details.
Popularity: 69
Several reasons. Your rotors could be warped. Its possible the proportioning valve isn't working correctly. Try a different type brake pad material. Make sure your wheel bearings are not too loose.Answerhave you cleaned and lubed the caliper rails?Answer -One of the most overlooked tasks when perfor…
Popularity: 56
The rubber gasket failure.
Popularity: 5
Hydraulic pumps work the same as any other pump, the difference is the controls used to direct the fluids where it needs to go to work what it is applied to.Most hydraulic pumps have 2 identical gears next to each other and they push the fluid in the troughs on the outside walls of the pump to the p…
Popularity: 64
Behind the rear seat under the well cover the motor will tell you what to get their is a rubber plug in the top of the motor that's were the fluid goes. Hope this helps.
Popularity: 17
The tank for the top motor fluid is in the trunk under/ near the spare tire. I think it is on the left side. You have to pull back the trunk lining. It takes power steering fluid also dot three brake fluid,
Popularity: 13
If you can get the solid rubber ones as replacing the oil filled ones that should not be a problem for an 8 year old car. See this: http://www.aa1car.com/library/motor_mounts.htm "Replacement mounts may or many not have the same construction as the original. Fluid-filled hydro-mounts are expensiv…
Popularity: 6
PTO, hydraulics, or neither The first thing you need to know is whether the tractor has a PTO (Power Take-Off) or built-in hydraulics. Given the age of the tractor in question, likely it either has a PTO or neither. If it has hydraulics, you should be able to attach the splitter. This may require t…
Popularity: 52
Answer Assuming you have checked the hydraulic fluid and it's OK, you could look into replacing the seals on the compression cylinder, but with jacks as inexpensive as they are these days, it would be easier and maybe even cheaper to replace the jack. I routinely see two-ton jacks on sale at auto…
Popularity: 29
It may just need to have some oil added to it, they do lose some over time. There should be either a rubber plug or a screw in plug toward the top of the cylinder on the side. If that is not the problem, it has to be rebuilt, new seal put into it. If it is a name brand, rebuild kits are sometimes av…
Popularity: 3
no. motors POWER hydrolic pumps. hydrolic pumps cannot function at the fast rate needed to generate energy as motors do.Answer 2There is not necessarily any need for a hydraulic - or any other - motor to function at a fast rate, as you put it. A hydarulic pump may need to only turn at say 1 rpm and …
Popularity: 53
I assume you mean the pump for the convertible top. It is located behind the rear seat. Bottom cushion pops out (2 clamps at outer edges of seat). Remove rear seat back by removing seat belt plate at bottom of seat back and then lift seat back straight upward. Pump is located behind sound barrier fl…
Popularity: 1
How Hydraulically Driven Intensifiers Work Process fluid flows through the inlet check valve and fills the process fluid cylinder. Pressurized hydraulic fluid acting on the hydraulic piston strokes the piston assembly to the right. Process fluid in the right cylinder is forced through the discharge …
Popularity: 21
No. Presently electromagnetic brakes are not used in cars but the can be used If I may finish that..on trailers
Popularity: 16
4 Way hydraulic valves are often used with double acting cylinders. The valve usually has a handle that is used to change fluid direction. On the 4 way valve there will typically be 4 ports or openings for connections of hoses. Connecting hoses is done as follows: There will be an IN and OUT port an…
Popularity: 30
The hydraulic clutch on a 91 Chevy Cavalier is bled by slowly pumping the clutch and releasing the bleeder valve. The valve is closed and the process repeated until all air is removed.
Popularity: 1
How to add hydraulic jack oil to an hydraulic jack (floor jack or bottle jack). First, don't open the Check Valves! The most common mistake with a floor jack is to open one of the check valves (or their covers) instead of actually finding the fluid reservoir plug. Be sure you have found the filler …
Popularity: 71
Large Commericial Jet ===Fuel Most large commericial jets operate on diesel fuel. The fuel is distributed over several fuel tanks distributed within the wings and the center fuselage. The Fuel Control system is a computer that helps the flight crew distribute the fuel in order to maintain the aircra…
Popularity: 28
use a one man bleeder
Popularity: 2
Among other reasons, oil is a natural lubricant, it doesn't evaporate readily, and it doesn't support corrosion. Oil has a much larger temperature range in which it stays a liquid.
Popularity: 27
http://www.hyjacks.com/H7.HTM is a simple description of how a jack works, and how to service one. Best info I could find and it worked for me. If the link is no good for some reason, it says to put the jack on a flat level surface and jack it all the way up, drop it back down, then open the FILL p…
Popularity: 2
The Roman scientist and inventor, Archimedes, was one of the first to invent the lift in 236 BC. His machine was for lifting heavy stones used for building. The modern lift was invented by Elisha Otis in the mid 1800's. Others had tried to design a lift, but failed because of the lack of brakes. Eli…
Popularity: 0
The runaway speed of a hydraulic turbine is the speed at which the turbine coupled to the generator runs at the maximum possible speed due to loss of load and this happens until the shut off valves completely closes the discharge from the penstock. the runaway speed of the turbine is determined by …
Popularity: 4
Answer Spool dynamics include fluid motion actuated by one or more tangential forces, i.e, gears, and thus achieve force as a function of mass acceleration. Mass of small gas engine flywheel spins, creating torque, applied through a coupler into a hydraulic motor, oh no, more gears, only …
Popularity: 28
The electrical ones improve on several things including packaging so the engineers can mount the rack where and how they want.The car can very easily have variable rate power steering.Unfortunately many of the electric boost systems have proven to be unreliable and very expensive to repair.The hydra…
Popularity: 2
I found a very thorough answer to this on Edmunds.com, check the 'related links' below. This is what it says: Electric-/hydraulic convertible top pertains to a closed hydraulic system. As a rule, a filling is only required after opening hydraulic circuit (e.g. after replacing parts). Remove CD pla…
Popularity: 5
hydraulics is the use of an incompressible fluid to perform work by displacing areas, which will create either linear or rotary movement of actuators.
Popularity: 10
Hydraulic system make use of hydraulic devices to perform a variety of functions.
Popularity: 1
Am not a 100% sure about this answer but yes it does hold some water in it, the portland cement majorly has its use in well aerated places i.e its mainly used for construction above sea or simply iits used where cement can dry in air but the hydraulic has properties enabling it to harden properly u…
Popularity: 1
dumptruck hydraulic pump is filled from a separate tank installed on truck it is either hanging off chassis rails on side,between dump bed and cab,or it is between rails under neath dump bed. if under dump bed,u can fill with a hose with funnel joined to hose, takes a while to do this . or if truck…
Popularity: 24
Magic!
Popularity: 8
Instrumentation Engineers are responsible for the design, construction and maintenance of instruments and entire instrumentation systems considered being the eyes and ears of any industrial undertaking. The type of instruments needed for ensuring better quality and efficiency of the end product are …
Popularity: 56
using the piping connection and also use meter gauges for measuring purpose.
Popularity: 1
Hydraulics are suitable for higher forces & precise motion than pneumatics. This is because hydraulic systems generally run at significantly higher pressures than pneumatics systems. Movements are more precise (repeatable) because hydraulics use an incompressible liquid to transfer power whils…
Popularity: 27
They create solutions to problems encountered by society. I build x-ray machine for airports. King's college London???In addition the solution in many cases leads to manufacture and therefore in many cases create employment.Interestingly though what the term "An Engineer" actually means some say any…
Popularity: 23
Have a helper pump the clutch pedal several times then hold it down. On the slave cylinder, loosen the bleeder valve until fluid starts to flow. When the fluid stops, snug the valve up and have the helper pump the pedal again and repeat the process. When the fluid comes out with no air mixed in it, …
Popularity: 1
a Chinese person
Popularity: 3
Malcolm Lockheed in 1918.
Popularity: 6
Fluids are incompressible, relatively speaking, hence the pressure applied through the system is directly transmitted to the object which you want to lift. If you used a gas, you would waste a lot of energy compression the gas-hence the system would be inefficient.  There's another reason. Hyd…
Popularity: 24
Yes, all clutches on KA's are hydraulic.
Popularity: 12
there isn't a measurment for hydraulic radius as far as i know and if you g on any website about it it doesnt have any measurements at the end of it. Josh (A level geography student) hydraulic radius has a unit as it is the ratio of c/s area to the wetted perimeter i. e. A/P so unit of length....…
Popularity: 8
The plural of hydraulic is hydraulics. Creating the plural form of this word is accomplished by adding an s to the singular form.
Popularity: 0
Force=Area*PSIArea=Pi*R^2Hope this helpsFor a double-acting cylinder:pi/4(d1^2-d2^2)ywhere: d1 = diameter of bore d2 = diameter of rod y = psi of system
Popularity: 15
Hydraulics are used almost in all vehicles .it is used in jcb's,cranes etc.
Popularity: 1
The exact bore measurement is 101.6 mm.
Popularity: 2
mines just snapped so its definitely cable....
Popularity: 2
Ones name is pneumatic and the other is hydraulic! (That doesn't really help)
Popularity: 5
ANSWER: No. Water under pressure doesnt have the mass for the stress placed on brake fluid or hydrolic fluid. Water is best used for cooling. It will still cool at 700 degrees F, at this point it is considered a plasma. Hydolic fluids such as brake fluid, transmission fluid and hydrolic fluids or…
Popularity: 11
Pascal's Principle
Popularity: 4
you can smell it hydrolic oil has a distinct smell to it AnswerHydraulic fluid is almost always thinner than motor oil.  motor oil is slightly slick if you rub it between you're fingers. hydraulic fluid will fell the same as brake fluid when rubbed between you're fingers.motor oil (new) will (…
Popularity: 7
There is air in the tank. leave hole open and jack. slowly close hole (or release valve) until closed. should being to jack
Popularity: 1
No, they are not. They are removable, but i do not suggest reusing them. They are hydrolic lifters and have a spring in between them. The following web address you will find them on the page I have posted for you. They are 50% of what napa is asking for them. A really good place to buy engine parts.…
Popularity: 37
Hydraulic brake systems use the fluid to transfer the force from the brake pedal to the braking system. Fluids can not be compressed. Air bubbles can be compressed and will make the braking system less effective.
Popularity: 1
Fluid pressure to the surface.
Popularity: 0
Wouldn't recommend it. Hydraulic fluid has to pass a different set of standards than motor oil. Motor oil has tackifiers, lower sulfur content and other ingredients that could prove harmful to the seals and other components in a hydraulic system. If it is an emergency only should you do it. -------…
Popularity: 22
With my 2 floor jacks of a different stripe, both are configured with a short fine-threaded hex head bolt that serves as both drain and fill orifice, located topside of the piston assembly. Be sure to release all compression prior to opening and throughout refill process. A squeeze bottle like the o…
Popularity: 3
yes, their are many types of hydraulic oils, for different specificate duties machine,s apply to.
Popularity: 3
If you are running low on hydraulic fluid, it could keep your machine from working properly. If the fluid is extremely low, it could cause permanent damage to the machine.
Popularity: 1
PRINCIPLES OF HYDRAULIC PRESSURE A Frenchman named Pascal discovered that a pressure applied to any part of a confined fluid transmits to every other part with no loss. The pressure acts with equal force on all equal areas of the confining walls and perpendicular to the walls. Remember when you are …
Popularity: 11
Depending upon the use, it can be a 3 phaze or 1 phaze induction motor. For domestic use it has to be a 1 phaze Induction motor but for industrial use it can be a 3 ph or 1 ph I.M.
Popularity: 3
We generally think of a hydraulic system as that collection of components and conduits that is used to transfer power to do work. But that's a bit dry when said like that, so let's get dirty and build a system to do something useful.We need a pump to pressurize the fluid, and a motor to drive the pu…
Popularity: 4
An Hydraulic system (and a pneumatic one as well) is simply a system using fluid to transfer energy from one point to another. When I press the brake pedal, the brake cylinders at the wheels operate. Coupled together by an hydraulic system.
Popularity: 9
It works jusy like your brakes. pump thgem then hold release the bleeder then tighten back up then pump 3x's and hold, crack the bleeder loose then tighten, pump and hold. When the air stopps coming out it is bleed. The bleeder is located right above the hydraulic line on the drivers side of tranny …
Popularity: 10
Check with the manufacturer. There are website for all major companies and they provide addresses for repair facilities.
Popularity: 12
first off, does the jack have hydrolic oil in the resevoir? if not, fill it up and try again. if this still doesnt work the "o" ring has probably rotted and needs replaced or just go buy a new jack. hope this helps you.
Popularity: 1
you put a new seal kit in it on a tractor ore what
Popularity: 4
Perhaps this is that state that allows fish and divers to offset their natural buoyancy and rest effortlessly in the depths.
Popularity: 1
One similarity is that they both use fluids. Both gasses and liquids are fluids. the two are also compressible.
Popularity: 3
A hydraulic system is a mechanical device used to move liquids. In a vehicle it moves the transmission fluid and gasoline.
Popularity: 0
A hydraulic lift works by having pressure travel through a tube into another. One tube is smaller forcing air into the larger one in order to push and raise the lift.
Popularity: 0
A Monobloc pump is a pump in which all rotating parts are mounted on a common shaft. The main components of a Monobloc pumps are Pump assembly and Motor assembly. Since there are 7% losses in belt driven sets and 3% losses in coupling driven sets hence to avoid these transmission losses Monobloc pu…
Popularity: 3
cars-used to breakgas pumpsdishwashersrollercoasters
Popularity: 1
The hydraulic jack is fabricated in pieces and is inserted into the actual hydraulic breaking system of the vehicle. Unions and ball valves along with a directional control valve allow the jack that is mounted on the chassis to be activated with brake pedal access.
Popularity: 1
A centrifugal pump is one that is used to transport the fluids throughout a vehicle. It uses this pump to get the fuel to the areas it needs to go.
Popularity: 1
A barometer is an instrument used to measure the atmospheric pressure. It does so by comparing the atmospheric pressure with a predefined standard pressure.
Popularity: 4
Hydraulics can be used basically everywhere in day to day life. They are used in your heart, in car brakes, in water pistels and also in vehicles like diggers and cranes.
Popularity: 2
yes a motor can be used in place of a pump on most applications. the difference between a pump and motor is the intake and discharge port sizes. on a motor they are the same i.d. on a pump they are different the intake port is larger than the discharge not sure what you mean by hydraulic motor.but…
Popularity: 20
There is a bleed screw on the cylinder on the tranny. This takes two people, one to work the pedal and one at the beeder. Works just like bleeding brakes. Be sure to check fluid often. Push pedal down while partner opens valve and close it when pedal reaches floor. Good communication with your partn…
Popularity: 5
a hydraulic jack is a mechanical arrangement that uses the power of fluids(hydraulic - study of mechanical property of fluids) to lift really heavy objectsIt consists of two enclosed containers connected to each other with a certain volume of liquid between them.Each of this containers has a piston …
Popularity: 5
I honestly have no clue what the formula is so if i don't someone needs to figure it out!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Popularity: 0
yes it is with the slave cylinder being inside the bee housing. the clutch master cylinder reservior is to the right facing the firewall. it requires brake fluid
Popularity: 15
1. car fuel pump 2. excavator 3. human heart
Popularity: 12
Hydraulic lifts utilize a hydraulic piston or ram, typically oil filled, to supply the lifting force for raising or lowering an object/load. These hydraulic systems are usually subdivided by the initial force that drives the hydraulic pump which supplies pressure for the piston. Air/Hydraulics (air …
Popularity: 7