0
A Fixture unit is 7.48 gallons (1 cu ft) or 3 sq ft of drainage Or a pump discharging 1 GPM = 1 FU
When in doubt of a proper answer ask a Master plumber of a class A journeyman
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Which item would be used to determine that a cold water supply to a dwelling would be adequate to serve the plumbing appliances?
There is no one item..Sizing the proper size of a water main one has to calculate the fixture unit demand . A fixture unit is one cubic foot of water (7.48 gallons) and each fixture is given a rating then one has to figure in friction losses through piping and fittings and developed lengh. To much velocity you will have erosion and lots of noise plus hydraulic shock (water hammer) to little allowances for the demand and you can experience a severe pressure / volume drop
What is the formula for calculating the full current load of a 400 watt metal halide light?
For the amperage of a metal halide fixture look for the nameplate which can be found on the side of the ballast. There it will tell you what the amperage of the fixture draws. Knowing what one fixture draws will allow you to size the lighting circuit for wire and breaker sizes.
What is One everyday use of a series circuit?
The average light fixture is likely in series with the light switch, and the utility power grid.
The hyperlink data type stores data that can have one of two values?
yes/no data type stores only one oftwo values
How can you tell if you have a trap in a drain line?
If you have a floor drain, there is a trap on the bottom of that. The main line shouldn't have a trap in it. There does not need to be one on the main because each fixture should have one and that's just another place for a clog to form.
How many litres are into one fixture unit?
In plumbing, a Fixture Unit (FU) is equal to one cubic foot of water per minute. A Fixture Unit is not a flow rate unit but a design factor. This is roughly 7.48 gallons per minute, or 28.3 liters per minute.
What is the volume of the average bathroom?
One fixture unit
How many fixture unit is in 1.5 liters?
There is no answer as the units are incompatible and therefore not convertible. In plumbing, a Fixture Unit is equal to one cubic foot of water drained in an 1 1/4 pipe over one minute. A Fixture Unit is not a volume or a flow rate unit but a design factor.
What is the Flow rate of one fixture unit?
3 gpm
What is fixture unit?
A fixture is 7.48 gallons which is equal to 1 cubic foot of waterAlso a fixture unit in storm drainage is roughly 3 square feet depending on pitchTo convert sanitary /waste to storm fixture units for a combined system one has to do interpolation combining all the GPM flow expected from a 10 year frequency
How do you convert water fixture units to gpm?
A fixture unit is 1 cubic foot of water (7.48 gallons) If your using pumped drainage /soil system then for every GPM of flow rate one has to consider it as ONE FU
How do you find out what size pipe you should run for certain distances?
The plumbing code adopted by the jurisdiction in which the piping is placed will assign a "fixture unit" value to fixtures. For example, for waste and vent piping, a lavatory is usually one, a sink is usually two, a toilet usually between three and six, etc. A chart in the code book will tell how many "fixture units" can be installed on a particular size line. For example, a 2" line will usually carry 16 fixture units on a vertical pipe, 8 fixture units on a horizontal pipe, and will vent 24 fixture units. For a specific answer to your need you should consult a plumber working in your jurisdiction. And as far as "certain distances".....horizontal is self-limiting by grade, vertical is addressed by code, for example, 2" is limited to 85 feet vertical. Pressure pipe (water) is done much the same way....fixture unit values assigned to fixtures and then total fixture units allowed for each pipe size and pressure range.
Which item would be used to determine that a cold water supply to a dwelling would be adequate to serve the plumbing appliances?
There is no one item..Sizing the proper size of a water main one has to calculate the fixture unit demand . A fixture unit is one cubic foot of water (7.48 gallons) and each fixture is given a rating then one has to figure in friction losses through piping and fittings and developed lengh. To much velocity you will have erosion and lots of noise plus hydraulic shock (water hammer) to little allowances for the demand and you can experience a severe pressure / volume drop
How much is one unit?
one unit is
How do you rate fixture units?
By the flow rate in GPM .. 1 GPM pumped discharge is considered ONE FU .. Normally a fixture unit is one cubic foot of water which is 7.48 gallons. Fixture can also be used for storm drainage such as a roof and then you have to figure 3 sq ft =1 FU and a combination system one has to use interpolation to size the drainage /waste line
What is fixturing?
A fixture is 7.48 gallons which is equal to 1 cubic foot of waterAlso a fixture unit in storm drainage is roughly 3 square feet depending on pitchTo convert sanitary /waste to storm fixture units for a combined system one has to do interpolation combining all the GPM flow expected from a 10 year frequency
What is a dranage fixture unit equal to?
A fixture unit is 1 cubic foot of water 7.48 gallons, it can also be square footage of an area to be drains depending on pitch how big the drain pipe isA basin is considered 1 FU as it is the amount of water that can be drained in one minute based on a cubic footA pump discharge of 1 GPM of pumped discharge is considered1 FU
