0
A good amount of solder is less than one drop, and should be applied through a very hot and clean gun, also making sure that you are using a new solder wire, avoid using solder from already soldered components because it will be having no zinc chloride.
Maynard Windler
Add your answer:
Earn +20 pts
Could soldering your motor harm it?
Yes, if too much heat is applied.
How to solder wire without a solder iron?
It is difficult to solder without the soldering iron, but not impossible. So, let’s talk about how to solder without a soldering iron. Getting a Heat Source Since you don’t have a soldering iron, you are going to need a heat source to heat up the various parts and the solder itself. In this case, it means having an open flame or heat source to provide the heat needed to melt the parts. The most important thing to keep in mind is that your heat source needs to be able to heat up the solder to its melting point, which is going to be between 400° and 700° Fahrenheit, or about 200° to 370° Celsius. Things like normal butane lighters, oil lamps, alcohol burners, candles, and even open flames like a campfire should do just fine for this task. Some people even choose to use a thick tin can and create a small and contained fire inside. As long as your heat source can melt the solder, you will be fine. Soldering by Heating the Wires Directly The easiest way to solder with a soldering iron is to twist the wires together and heat them directly. It doesn’t require a soldering iron and is quite easy to do. If you are soldering wires, strip the insulation off the ends of the wires to be soldered together. Now, twist the ends of the wires together with a few rotations. Make sure that the wires are twisted tightly together. What you want to do here is to heat up the wires using your open flame. Make sure to not heat up the insulation past the exposed wires too much, as this can cause its own problems. Let the twisted wires heat up for about 20 seconds, then slowly apply a thin layer of solder to them. The solder should melt right onto the wires, but if it does not, heat up the wires more to make it melt. You don’t want a cold solder joint as these are not effective. Now that you have the solder connection, you can cut off the rest of the exposed wires past the point of the solder. Using Small or Large Heat Sources for Soldering If you are working with a small heat source, such as a candle or a lighter, you need to use a small soldering iron, like the tip of old scissors. The best thing is 14-gauge steel wire, as it heats fast, but retains heat fast enough to solder with. The wire is easy to bend into shape for various soldering positions. Nails and screwdrivers work too. Now you want to use your lighter or candle to heat the soldering tool of choice. Heat it about ½ inch from the very tip, as this will help prevent damage and oxidation. Allow the wire, nail, or other soldering tool of choice to heat up for about 20 seconds, then move quickly to solder the components that require soldering. If necessary, keep repeating this process until you are done. Conclusion is that it is not impossible to work on solder without soldering iron.
What is soldering wire?
Solder is a group of metallic alloys that melts at a relatively low temperature and is generally used to connect other pieces of metal together. The low melting point makes it useful for some applications, especially electronic circuitry and some plumbing applications, though it should be noted that plumbing solder is a different alloy than electronic solder and plumbing solder has little or no lead to minimize lead exposure to the people who drink the water. Having described what solder IS, soldering wire is just that, its a wire that is made of solder. Solder wire is useful when working on electronic circuits since it allows the user to control how much will be put on an electronic connection. Solder wire comes in several sizes, as well as with or without a flux core. Flux is a material (usually either acidic or rosin) that encourages melted solder to flow onto other metals, usually copper, iron or brass. Other types of solder are available for use on materials such as aluminum, but solders should match the application to match the type of metals you are joining.
What does sodder mean?
The actual word is solder. It's just pronounced "sodder". One could compare soldering to welding, but on a much, much smaller scale. It is a way to join metal parts, usually for electrical connections.
How long it takes to solder 40 pin connector?
How neat does it have to be? ;-) Seriously, in a commercial environment a circuit-board mounted 40-pin connector can be wave soldered in less than a second. By hand, with optimal soldering equipment and quality solder, you can figure on about 1 second per pin (soldered correctly, without too much or too little solder) to a circuit board. Soldering wires takes about 5 seconds per pin, assuming that the ends are already stripped, tinned and properly aligned (not mix & match/hard to find).
What is the purpose of flux in the soldering process?
Soldering usually applies to electronics, but can be used in many different applications. Soldering in electronics is done by melting solder (in this case, a small hollow wire made up of 40 percent lead and 60 percent tin), which contains rosin (flux) in the hollow core. The purpose is to secure the electronic parts to the circuit board. Desoldering is a removal of the solder already used, to release the parts from the circuit board so that a replacement part can be installed and soldered into place again. I do it all the time as a matter of course and I can tell you first hand, it's not rocket science. Knowing the difference between a good solder connection and a bad connection when you're through isn't hard, but most hobbyists usually don't pay that much attention to the quality of the joint.
How a Soldering Station Can Improve Efficiency?
If you consider yourself a plumbing or electronics expert, then you are no doubt familiar with how to use a soldering iron. However, there are a lot of people out there who never give a second thought to whether or not they should invest in a soldering station. While it may seem like a really simple thing, a soldering station is really much more useful than you might imagine, and it makes sense. A soldering station is specifically designed to have a place for all your necessary tools and supplies, making it much easier to get what you need when you need it.
How much does soldering iron cost?
They range enormously; from around £6 up to hundreds of pounds for a top of the range soldering station.
What is the best soldering iron and tip to use on circuit boards?
Soldering irons come in a variety of sizes and shapes. There is a wide selection of soldering irons, soldering pencils, soldering stations and soldering guns available on market in the USA.Which soldering iron is the best soldering iron for you depends on the soldering work you are planning to do and how often you are planning on using your soldering iron. The following four factors should be taken into consideration when picking a soldering iron that will be used for soldering projects on circuit boards:1) ) type of the soldering tools2 wattage of the soldering iron3)temperature control4) tip size and shapeTypes of soldering toolsAll soldering tools can be divided in four different groups-Soldering pencils-Soldering station-Soldering rework /repair stations systems-Soldering gunsSoldering pencilsSoldering pencils are the simplest (and the cheapest) soldering tool. Soldering pencils are good only for simple do-it-yourself projects. The price range of the soldering pencils is $10-$30Soldering stationsSoldering station consists of two parts: soldering pencil and a power station. Soldering pencil is attached to a power station. Power station controls temperature of the iron tip in the wide range. It automatically keeps the iron tip at an appropriate temperature. Desired temperature of soldering iron is set with knob on the face plate of power station. Soldering station can be used for most of soldering projects. It can be used for soldering of through-hole components on circuit board as well as for soldering of very fine surface-mount components as small as 0603 and 0805. The price range of the soldering stations is $40-$150.Soldering rework /repair stations systemsSoldering rework/repair systems are complex soldering tools which are mostly used in industry or in the high-volume manufacturing facilities. This soldering systems are the most expensive soldering tools since they usually consist of power station and 4 or 5 hand pieces including soldering iron, hot-air gun, tweezers , vacuum pump which is used for the de-soldering work. The price range of the soldering systems is $250-$2500.Soldering gunsI do not recommend using soldering guns for fine soldering projects on circuit boards.The most popular brand names for soldering irons in the USA are Weller, Pace and Hakko. Aoyue soldering irons are less popular brand name in the United States then Weller or Pace. However, Aoyue soldering irons are much cheaper and they are good combination of quality and price.There is a wide selection of iron tips. Iron tips come in different shapes and sizes. For most soldering projects you can use screwdriver tip 0.062" or 0.032". For fine soldering projects and for soldering of small surface-mount components you can use conical tip 1/16".ConclusionI recommend a temperature controlled 50W soldering station. This soldering station will be excellent tool for most of soldering projects. My top recommendations are:-Weller WESD51 soldering station (digital)- Weller WES51 soldering station (analog)- Hakko FX-888 soldering station- Aoyue 2702A soldering station- Pace ST-25 soldering station
What are the six types of bad solder connections?
Six types of bad solder connections include a cold joint with insufficient wetting (Pin) or insufficient wetting (Pad), a disturbed joint, an overheated joint, too much solder, or not enough solder.
How much does NFL player Nate Solder weigh?
NFL player Nate Solder weighs 320 pounds.
Where is the headlight relay for a Ford Explorer?
The head light module is located under the center console near the front. Pull out the top pieces and should be in the right front corner inside the console. It is in a plastic box and can be pulled out with out much effort. The soldered connections on the board work their way loose. If you can manage a soldering iron you can flow the solder back and reuse the module. Hope this helps.
