0
What should be the setting for a dual voltage selector switch on a power supply when using a computer in the US?
Wiki User
∙ 8y ago
The 110VAC to 125VAC range (not the 220VAC to 250VAC range).
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
In the unknown of measuring the voltage what should be the setting of VOM selector?
Use the highest available voltage setting. One should know the system voltage before attempting to measure, other wise it may lead to accidents.
What is the incoming voltage from the current source to the transformer called?
the incoming voltage from the current source to the transformer is called primary voltage.....
What will happen to the resistance and the brightness if you add a light bulb to the circuit?
If a rheostat is connected in parallel with a light bulb, the setting of the rheostat should have no effect on the performance of the light bulb, as long as the power supply is able to maintain its output voltage and deliver the current demanded by their parallel combination.
Why Normal time-overcurrent relays are not adequate for generator backup protection?
Setting the time-overcurrent relays high enough to prevent tripping for normal overloads may result in them not tripping at all due to the decaying characteristic of the generator fault current. Using the system voltage to control the overcurrent characteristic resolves this problem, since the voltage should drop very little for overloads, but will collapse to a small value for external faults. The 51V protection function uses the system voltage to adapt the operation of a time overcurrent element, using either voltage-restraint (51VR) or voltage-control (51VC).
Technician A says that the current draw should decrease as the voltage decreasestechnician B says that the current should increase as the voltage decreases Which technician is right?
Both technicians are right, and both technicians are wrong, because not enough information is present in the question, nor in their statements. Given constant impedance, current should decrease as voltage decreases, while given constant power, current should increase as voltage decreases.
What should be the setting for a dual-voltage selector switch on a power supply when using a computer in the US?
The 110VAC to 125VAC range (not the 220VAC to 250VAC range).
In the unknown of measuring the voltage what should be the setting of VOM selector?
Use the highest available voltage setting. One should know the system voltage before attempting to measure, other wise it may lead to accidents.
What position should the output voltage selector be set when using the constant speed motor?
Variable
When an AC voltage is being measured across a 15 resistor which is carrying a current of 12 amps the selector switch should be set to the AC voltage position of 2 volts 200 volts 20 volts 1000 volts?
Two Hundred
Is the voltage regulator in the computer on a 1987 Dodge Lancer?
Should be located in the back of the alternator
Which is the correct voltage division setting for testing a throttle position sensor?
Volt meter should be in a 5 volt scale.
Why does your computer go into standby and then restart when you try to type?
This is most likely caused by a setting on your computer that enables energy saving for your keyboard. Disable this setting and it should work normally again.
When measuring an unknown value of voltage the meter should be initially set to?
With an unknown voltage you should start out with the highest voltage setting on the meter. Doing this reduces the risk of "pegging" out the needle on an analog gauge or overloading the input of a DMM. Most DMM's are auto-ranging though.
2004 jeep tj 4.0 what should alternator be putting out voltage?
13-15 volts, depends on what the computer wants.
What is the RPM speed recommended for setting the timing on 1991 mustang 5.0?
Timing and idle setting maybe computer controlled and not adjustable. If they are adjustable should be 825-850 RPM
At what voltage should hair dryers be set?
The voltage for anything should match the supply voltage.
What digital multi meter setting should be used to measure voltage?
There are settings for AC and DC voltages. If they are not marked as such, the DC setting might be parallel lines and the AC marking may be a cycle of a sine wave (Wavy line).
