The breaker type be it a single pole or double pole will depend on what voltage the air conditioner operates on. Once the voltage is established, the sizing of the breaker depends on what the current draw of the air conditioner is.
Answer for USA, Canada and countries running a 60 Hz supply service.
The type and size of the breaker to use on an air conditioner will depend upon the specifications of the air conditioner. This information will be found on the conditioner's nameplate. If the voltage is 120 volts a single pole breaker will be used. If the voltage is 240 volts a two pole breaker will be used. The amperage of the breaker should be within the amperage stated on the nameplate. Some air conditioners are of such a size that they can not be plugged in and have to be hardwired. These installations should be done by a qualified electrician and he will know the wire size and size of the breaker required to protect that size wire.
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Size the breaker at no less than 125% of your expected load. Make sure the voltage is correct, as well.
It depends on how much amperage your ac pulls. It could be a 30a, 40a, or 50a breaker on a dedicated (isolated) circuit.
Depends on the HVAC unit in question. Contact the manufacture or read the installation instructions that came with the unit.
60
You need a 60 amp breaker.
My 3 ton geo unit uses a 30 amp breaker. That is probably more than adequate because it also is for the vertical loop pumps in the ground. The back-up heat strips however, use a 60 amp breaker (on my system.) I'm not sure but I would say yours probably needs that too. Good luck!
If it is a portable generator the breaker should be self contained within the generators panel. If the generator is a stationary standby unit a voltage has to be stated to calculate the conductor size and hence the breaker size to protect the conductor. Amps = Watts/Volts.
When installing a circuit breaker, you size the breaker based on the wire size. The breaker should be matched to the ampacity of the wire to ensure proper protection against overloads and short circuits. The device being controlled by the breaker is not a determining factor in sizing the breaker.
What size of central and heat unit do you need for 916 sq ft?
You should not have to calculate the watts of the unit. All the information that you need will be on the nameplate of the unit. It is this information that electricians use to calculate the conductor size and breaker to supply the power to the unit.
60
50amp but if considering the breaker cannot withstand starting current you need to size the breaker up.
You need a 60 amp breaker.
6
8 AWG is typical.
My 3 ton geo unit uses a 30 amp breaker. That is probably more than adequate because it also is for the vertical loop pumps in the ground. The back-up heat strips however, use a 60 amp breaker (on my system.) I'm not sure but I would say yours probably needs that too. Good luck!
It is not the number of bulbs that you worry about. It is the wire size that is your concern. If the circuit is wired with AWG 12/2 wire then use a 20 amp breaker. If it is wired with a AWG 14/2 wire then use a 15 amp breaker. You are protecting the wiring with the correct size breaker.
This formula will give you the amperage I = kw x 1000/1.73 x E x pf (pf = power factor). Take the amperage and multiply it by 125%. This will give you the breaker size that you need.
When installing a circuit breaker, you size the breaker based on the wire size. The breaker should be matched to the ampacity of the wire to ensure proper protection against overloads and short circuits. The device being controlled by the breaker is not a determining factor in sizing the breaker.
If it is a portable generator the breaker should be self contained within the generators panel. If the generator is a stationary standby unit a voltage has to be stated to calculate the conductor size and hence the breaker size to protect the conductor. Amps = Watts/Volts.