0
Related Photo: http://www.makingthemodernworld.org.uk/icons_of_invention/img/IM.1201_el.jpg This radio is the first working device to use a printed circuit board (PCB), the electronic technology invented by Paul Eisler. An Austrian refugee in London, Eisler made this radio in 1942, following on from initial experiments in 1936. At the time, it was usual to interconnect all components in electronic goods with hand-soldered wires, a method of manufacture which did not lend itself to any high degree of automation. First applied in proximity fuses for anti-aircraft missiles, PCBs have subsequently found near universal application in electronic goods, yielding highly miniaturised devices which can be mass produced.
Wiki User
∙ 16y ago
Wiki User
∙ 11y agoIt was designed on Tuesday the 12th of june 1926
Add your answer:
Earn +20 pts
What does a circuit board look like?
A circuit board consists of numerous electronic components, depending on the application, these components can be in the thousands or in the ten's, therefore circuit boards vary in numerous sizes, all connected using very fine electrical connection strands.
When was the first ROV developed?
the first ROV was developed in 1953
Where were blueprints first developed?
British
Who developed the first fireplug?
george smith
What is the first technology developed by man?
fire
What is the lifetime of printed circuit board?
Depends on the material it's constructed from, the application for which it's being used and the atmospherics to which it's exposed. I have printed circuit boards from the very first model of an RCA transistor radio made in 1957 and the circuit board as well as the electronics still work.
How do you grind up a circuit board?
To grind a circuit board, the individual electronic components have to be removed first. The circuit board is usually ground industrially and recycled for a number of functions.
What are the four steps for correctly soldering components to a printed circuit board?
1. Remove the soldering iron from the holder and wipe the tip on a sponge. 2. Heat the joint to be soldered. 3. Apply solder to the joint. 4. Apply a small bit of solder to the tip of the soldering iron and return it to the holder.
Who invented the first circiut board?
Paul Eisler invented the first circuit board in 1936.
How do you replace the wiper motor circuit board?
This is really an easy fix. The wiper motor assembly is on the firewall, just right of center. The wiring can be unplugged before the circuit board is removed, or afterward. I found it easier to unplug it after the circuit board was removed. There is a flat cover that is held on with three torx screws (T20). Remove those screws and remove the cover. The circuit board will now be visible. Remove the circuit board by grasping the wiring connecter and gently pulling it towards the front of the vehicle. When the circuit board has fallen free, unplug it from the wiring harness if you haven't already done so. The solder joints that connect the wiring socket to the board were bad on my board. I just resoldered those and re-installed the circuit board. I did get an entire wiper motor assembly, which included the board, from a salvage yard for $40. I didn't even use it. Excellent answer! My wipers would not start without getting out and helping, then they might or might not continue running after a few wipes. When switched on and not running, module would produce buzzing sound. Followed directions above, and even though the three pins joining the wiring harness plug to the circuit board looked properly soldered, carefully re-soldered making sure to have good solder contact to printed circuit strips. In my case this worked like a charm, and judging from the number of postings for this fix, it seems to be a common problem with this board. It would seem to be a good first step unless there are other obvious signs of failure.
What organization developed the first national building code?
National Board of Fire Underwriters in 1905
How is current measured in a series circuit?
Current is measured in a series circuit by the use of a multimeter. First, the power source must be attached to the circuit board. The board is attached to the multimeter, then that is attached back to the power source.AnswerCurrent is measured either with an ammeter, or with a multimeter set to measure current. The instrument must be connected in series with the other components in the circuit.
Who made The first successful printing press was developed by this man?
The first successful printing press was developed by Johannes Gutenberg in the 15th century. His invention revolutionized the dissemination of information and the spread of knowledge by making printed material more accessible and affordable.
When was the Bible first printed?
The earliest bibles - indeed all books - were written by hand, the first printed bible was the Guttenberg Bible, printed in 1454 or 1455.
What was the first thing printed on the first printing press?
The first thing to be printed on a printing press was the bible.
When were the first Christmas cards printed?
The first Christmas cards were printed in the year 1843.
What was the first apple?
The first computer made by Apple was the Apple I this was followed by the Apple II and then the Apple III. The first apple tree was grown in the Nile river valley.
