0
Which rifle??? Which model, so, you left too many variables to answer directly, however if you allow me to get on my soap=box,
I can are refer to a magazine for the notorious Remington 597 in .17 cal,,,,, the answer is "they are junk"!!! The components are cheap, crudely made, ineffective, poorly engineered and otherwise "junk". They have been assembled by monkeys (they could not find a football).
Thank you, now that that is out of my system, most magazines function properly unless they are bent or damaged. Notice i said "most".. try another magazine or two to determine if it is the fault of the magazine or the rifle.
Try disassembling the magazine and polishing the edges of the parts so they slide better.... seems like you could spend a long time attempting a cure before you throw it away and simply buy another magazine.
Wiki User
∙ 16y ago
Remington magazine followers can jam due to various reasons, including dirt or debris buildup, worn out or damaged parts, improper assembly, or weak magazine spring tension. To address the issue, thoroughly clean and inspect the magazine, replace any worn parts, ensure proper assembly, and consider upgrading to a stronger magazine spring if needed.
Add your answer:
Earn +20 pts
What are the components of the magazine body in the M9?
The magazine body is a component, and is one piece. The components of the complete magazine would be the magazine body, the floor plate, the spring, and the follower. US Navy Answer: Locking block plunger, Magazine spring, magazine tube, follower, floor plate.
What are the parts of the m9 magazine assembly?
body, spring, follower
What type of magazine does a Remington model742 rifle holds?
A model 742 magazine
My Remington 870 mag only hold 2 2 34 in shells in the mag why is that?
In order to comply with migratory bird laws, Remington has installed a plug in your magazine. To remove it, simply unscrew the magazine cap, and I've seen two types of spring catches on Remingtons, so if it's a plastic one with a slot in it, press it in and rotate a quarter turn. If it's a C-Shaped metal ring, pull one end out with a screwdriver. Careful, as this will also release spring pressure. Tilt the shotgun forward, and the plug and your follower should drop out. Put the follower back in with the spring behind it, put back in the spring catch, and put the magazine cap back on the magazine. You should have a full capacity magazine tube now.
How do you fix a Remington 870 super mag from double feeding and jamming?
The answer lies in adjusting the primary & secondary shell stops.
How do you remove magazine tube on Stevens 87d?
To remove the magazine tube on the Stevens 87D, first ensure the firearm is unloaded. Then, unscrew the end cap at the front of the magazine tube. Slide off the end cap and follower, then push the magazine spring and follower out through the rear of the tube. Finally, slide the magazine tube out of the receiver.
Will a Remington 597 magazine fit in a 522 viper?
No.
Why does your Stevens 22 long rifle keep on jamming after the first shot?
Could be ammunition, magazine, dirty, etc..
Does Remington make a gun with a detachable magazine?
Remington makes multiple rifles with detachable clips. The 742 and 760 both have detachable magazines. The Remington model 700 can be readily altered to a detachable magazine, parts are sold in Cabela's, and other suppliers.
Which major component group consists of the base plate follower and housing m16?
magazine
What should you do to unjam your ak47 magazine?
If you're having problems with an AK mag jamming, you probably need to replace the spring. As for clearing the initial jam, typically, either the front or rear of the cartridges would be angled down further. You can apply pressure to the opposite end in order to try getting them level again. If that doesn't work, you'll probably have to remove the floor plate (be careful when you do this, and the pressure could cause the spring to shoot out), then pull out the magazine and follower. When you do this, inspect the follower while you're at it, to ensure it's not bent or otherwise deformed.
How do you remove a clip from a Remington 1911 handgun?
If you mean the magazine, there is a magazine release button on the left side of the gun. You press the button and the magazine comes out.
